POWER WINDOW REGULATOR MOTOR (for Sedan Front Side) > INSTALLATION



1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY FRONT


B127213
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using "Torx" socket wrench T25, install the power window regulator motor assembly front with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
  1. Apply MP grease to the sliding and rotating areas of the front door window regulator.

    NOTICE:
    Do not apply grease to the window regulator spring.


  1. w/ Power window:



      B136167E01
    1. Loosely screw bolt A onto the front door window regulator.

    2. Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.

      NOTICE:
      Do not drop the window regulator as it may be damaged.
    3. Install the front door window regulator with the 5 bolts, and tighten bolt A.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    4. Connect the connector.



    B136195E01
  1. w/o Power window:

    1. Loosely screw bolt A onto the front door window regulator.

    2. Insert the front door window regulator into the door panel. Use bolt A to hang the front door window regulator on the door panel.

      NOTICE:
      Do not drop the window regulator as it may be damaged.
    3. Install the front door window regulator with the 5 bolts, and tighten bolt A.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
    4. Connect the connector.



3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


B136186
  1. Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Do not damage the glass.


    B136165
  1. Install the front door glass onto the front door window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


4. INSTALL FRONT DOOR SERVICE HOLE COVER


B136187E01
  1. Apply butyl tape to the door panel, then install a new front door service hole cover as shown in the illustration.

    Specification:
    Area
    Dimension
    A
    2.0 mm (0.079 in.) or more
    B
    6.0 mm (0.236 in.) or more

    HINT:
    1. When installing the service hole cover, pull the links and connectors out through the service hole.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the quality of the seal.


5. INSTALL FRONT DOOR TRIM BRACKET


    B136164
  1. Install the front door trim bracket with the 2 screws.



6. INSTALL FRONT DOOR BELT MOULDING


    B134875
  1. Engage the 6 claws and install a new front door belt moulding.



    B134873E02
  1. Remove the protective tape.



7. INSTALL OUTER REAR VIEW MIRROR


B136162E01
  1. Engage the claw and install the outer rear view mirror with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
  1. w/ Power mirror:
    Connect the connector.



8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B136161
  1. w/ Power window:

    1. Connect the front door lock remote control cable and front door inside locking cable.



    2. B136160
    3. Engage the 9 clips and install the front door trim board.



    4. B136159
    5. Tighten the screw.



  1. w/o Power window:



      B136194
    1. Connect the front door lock remote control cable and front door inside locking cable.



    2. B136192
    3. Engage the 9 clips and install the front door trim board.



    4. B136193
    5. Tighten the screw.



9. INSTALL FRONT ARMREST BASE UPPER PANEL


B136158
  1. for Driver side with power window:

    1. Connect the connector.

    2. Engage the 7 claws and 2 clips and install the front armrest base upper panel.

    3. Tighten the screw.



    B141925
  1. for Front passenger side with power window:

    1. Connect the connector.

    2. Engage the 7 claws and 2 clips and install the front armrest base upper panel.

    3. Tighten the screw.



    B141926
  1. w/o Power window:

    1. Engage the 5 clips and 2 clips and install the front armrest base upper panel.

    2. Tighten the screw.



10. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


B136157E01
  1. Engage the claw and clip and install the front door lower frame bracket garnish.



11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }