REAR SEAT ASSEMBLY (for CrewMax LH Side) > REASSEMBLY |
for Preparation Click here
- CAUTION:
- Wear protective gloves. Sharp areas on the seat cushion spring and seatback frame may injure your hands.
1. INSTALL SEAT LOCK CONTROL CABLE SUB-ASSEMBLY LH |
Install the control cable to the seatback frame.
Connect the 2 cables.
2. INSTALL CENTER REAR SEAT OUTER BELT ASSEMBLY |
Install the outer belt with the bolt and nut.
- HINT:
- First install the bolt A, and then install the nut B.
- Torque:
- for bolt A:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
- for nut B:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Install the belt sensor with the 3 nuts.
- Torque:
- for nut C:
- 6.0 N*m{ 61 kgf*cm , 53 in.*lbf }
3. INSTALL REAR SEAT SHOULDER BELT HOLE COVER |
Install the seat belt as shown in the illustration.
Install the cover with the screw.
4. INSTALL INNER SEAT TRACK REINFORCEMENT LH |
Install the reinforcement with the 2 bolts.
- Torque:
- 22 N*m{ 224 kgf*cm , 16 ft.*lbf }
5. INSTALL REAR SEAT CUSHION SUPPORT ASSEMBLY |
Install the cushion support with the 6 nuts.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
6. INSTALL INNER REAR SEAT TRACK BRACKET COVER |
Install the cover with the screw.
7. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH |
Install the seatback frame.
Using a T55 "TORX" socket, install the 2 bolts.
- Torque:
- 55 N*m{ 561 kgf*cm , 41 ft.*lbf }
Using a T45 "TORX" socket, install the 3 bolts.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Install the bolt.
- Torque:
- 22 N*m{ 224 kgf*cm , 16 ft.*lbf }
8. INSTALL REAR SEAT CUSHION MOULDING LH |
Attach the 2 claws to install the moulding.
Install the 3 screws.
9. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
Attach the claw to install the cover.
Install the 2 screws.
10. INSTALL INNER REAR SEAT RECLINING COVER LH |
Attach the 2 claws to install the cover.
Install the screw.
11. INSTALL REAR SEATBACK HINGE COVER |
Install the cover with the 2 screws.
12. INSTALL CENTER RECLINING ADJUSTER INSIDE COVER |
Attach the claw and hook to install the cover.
Install the 2 screws.
13. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY LH |
Install the 3 bushes to the cushion spring. Then using a T45 "TORX" socket, install the 3 bolts.
- Torque:
- 22 N*m{ 224 kgf*cm , 16 ft.*lbf }
Install the 3 bolts.
- Torque:
- 22 N*m{ 224 kgf*cm , 16 ft.*lbf }
14. INSTALL CENTER UPPER LINK COVER |
Attach the 2 claws in the order shown in the illustration to install the cover.
Install the screw.
15. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH |
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
16. INSTALL REAR SEATBACK COVER WITH PAD LH |
Using hog ring pliers, install the seatback cover (with pad) with new hog rings.
Attach the hooks to the seatback frame.
Attach the 4 claws to install the bezel.
17. INSTALL LOWER REAR SEATBACK COVER SUB-ASSEMBLY LH |
Using hog ring pliers, install the seatback cover with new hog rings.
18. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH |
Connect the cable in the order shown in the illustration to install the lever.
Install the 2 screws.
19. INSTALL REAR SEATBACK LOCK STRIKER COVER LH |
Attach the 2 claws to install the cover.
20. INSTALL REAR SEAT HEADREST SUPPORT |
Attach the 8 claws to install the 4 supports as shown in the illustration.
21. INSTALL CENTER REAR SEAT HEADREST ASSEMBLY |
22. INSTALL REAR SEAT HEADREST ASSEMBLY LH |
23. INSTALL REAR SEAT ARMREST ASSEMBLY |
Install the armrest with the 3 nuts.
- Torque:
- 6.0 N*m{ 61 kgf*cm , 53 in.*lbf }
24. INSTALL REAR SEATBACK COVER |
Attach the 8 claws to install the 2 covers.
25. INSTALL REAR SEATBACK BOARD LH |
Attach the 5 clips to install the seatback board.
Install the 4 screws.
26. INSTALL REAR SEAT INNER BELT ASSEMBLY |
Pass the seat belt through the seatback hole.
27. INSTALL REAR SEAT CUSHION MOULDING REAR RH |
Attach the 2 claws in the order shown in the illustration to install the moulding.
Install the screw.
28. INSTALL REAR SEAT CUSHION MOULDING REAR LH |
Attach the 2 claws in the order shown in the illustration to install the moulding.
Install the screw.
29. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER LH |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
30. INSTALL REAR SEAT CUSHION COVER WITH PAD LH |
Attach the hooks to install the seat cushion cover (with pad).
Install the seat belts with the bolt.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.