SIDE AIRBAG SENSOR (for Regular Cab) > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SIDE AIRBAG SENSOR


    B165651

  1. Check that the ignition switch is OFF.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation

  1. Install the door airbag sensor with the screw.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the door airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the door airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the side airbag sensor.

  1. Connect the connector.



2. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH (for Front Side)


    B165684E03

  1. Connect the 2 cables to the inside handle.

  1. Attach the inside handle's knob to the door trim board.

  1. Attach the 10 clips to install the door trim board.



    B167314E01

  1. Install the inside handle and door trim board to the door trim panel with the screw.

  1. Install the door trim board to the door panel with the screw.

  1. Attach the clip.



3. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH (for Front Side)


    B165652

  1. Attach the 3 clips to install the front lower door frame bracket garnish.



4. INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (for Front Side)


    B165697E01

  1. Install the plate and regulator handle with the snap ring.

    HINT:
    With the door window fully closed, install the plate and the regulator handle with the snap ring as shown in the illustration.


5. INSTALL FRONT ARMREST BASE PANEL UPPER LH (for Front Side)


    B165649E01

  1. Connect the connectors.

  1. Attach the 2 clips to install the front upper armrest base panel.



6. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH (for Front Side)


    B165648E01

  1. Attach the 4 claws to install the bezel plug.



7. INSTALL REAR SIDE AIRBAG SENSOR


    B166507

  1. Check that the ignition switch is OFF.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

  1. Install the side airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the side airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the side airbag sensor.

  1. Connect the connector.



8. INSTALL FRONT DOOR SCUFF PLATE LH (for Rear Side)


B165843

  1. Attach the 6 claws and 3 clips to install the front door scuff plate.



9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


10. CHECK SRS WARNING LIGHT

  1. Check the SRS warning light (Click here).