DIFFERENTIAL CARRIER ASSEMBLY (for 3UR-FE, 3UR-FBE) > INSTALLATION |
for Preparation Click here
1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY |
Clean the contact surfaces of the rear differential carrier and rear axle housing.
Install a new rear differential carrier gasket and the differential carrier with the 10 washers and 10 nuts.
- Torque:
- 72 N*m{ 734 kgf*cm , 53 ft.*lbf }
- NOTICE:
- Be careful not to damage the contact surfaces of the differential carrier and rear axle housing.
2. INSTALL REAR AXLE SHAFT LH |
Install the rear axle shaft LH (Click here).
3. INSTALL REAR AXLE SHAFT RH |
- HINT:
- Use the same procedures described for the LH side.
4. INSTALL PROPELLER SHAFT ASSEMBLY |
Install the propeller shaft for 2WD (Click here).
Install the propeller shaft for 4WD (Click here).
5. ADD DIFFERENTIAL OIL |
Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.
- NOTICE:
- Too much or too little oil will lead to differential problems.
- After changing the oil, drive the vehicle and then check the oil level again.
- Oil type:
Item Oil type and viscosity Front differential Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent. Rear differential
- Front differential capacity:
Specified Condition 2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.)
- Rear differential capacity:
Engine type Wheelbase type Cab type Drive type Specified Condition 3UR-FE. 3UR-FBE 3220 mm (10 ft. 6.8 in.) Regular 2WD 3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.) 4WD 3700 mm (12 ft. 1.7 in.) Regular 2WD 3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.) 4WD Double 2WD 4WD CrewMax 2WD 3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.) 4WD 3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.) 4180 mm (13 ft. 8.6 in.) Double 2WD 3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.) 4WD 1GR-FE and 1UR-FE 3220 mm (10 ft. 6.8 in.) Regular 2WD 4.00 to 4.10 liters (4.23 to 4.33 US qts., 3.52 to 3.60 Imp. qts.) 4WD 3700 mm (12 ft. 1.7 in.) ALL 2WD 4.55 to 4.65 liters (4.81 to 4.91 US qts., 4.01 to 4.09 Imp. qts.) 4WD 4180 mm (13 ft. 8.6 in.) 2WD 4WD
for Rear Differential:
Install a new gasket and the filler plug.
- Torque:
- 49 N*m{ 500 kgf*cm , 36 ft.*lbf }
for Front Differential:
Using a 10 mm hexagon wrench, install a new gasket and the filler plug.
- Torque:
- 39 N*m{ 398 kgf*cm , 29 ft.*lbf }
6. INSTALL REAR WHEEL |
Install the rear wheels.
- Torque:
- for aluminum wheel:
- 131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
- for steel wheel:
- 209 N*m{ 2131 kgf*cm , 154 ft.*lbf }