AUTOMATIC TRANSMISSION UNIT > REASSEMBLY

for Preparation Click here



1. BEARING POSITION



C163084E01


Bearing and race diameter:

Mark
Front Race Diameter Inside / Outside
Thrust Bearing Diameter Inside / Outside
Rear Race Diameter Inside / Outside
A
74.3 to 74.6 mm (2.93 to 2.94 in.) / 87.4 to 87.7 mm (3.44 to 3.45 in.)
72.0 to 72.3 mm (2.83 to 2.85 in.) / 85.3 to 85.6 mm (3.36 to 3.37 in.)
-
B
38.0 to 38.3 mm (1.50 to 1.51 in.) / 53.9 to 54.1 mm (2.12 to 2.13 in.)
36.5 to 36.7 mm (1.437 to 1.445 in.) / 52.9 to 53.2 mm (2.08 to 2.09 in.)
-
C
-
21.1 to 21.3 mm (0.83 to 0.84 in.) / 39.5 to 39.8 mm (1.56 to 1.57 in.)
22.8 to 23.1 mm (0.898 to 0.909 in.) / 44.5 to 44.8 mm (1.75 to 1.76 in.)
D
-
39.5 to 39.7 mm (1.555 to 1.563 in.) / 60.5 to 60.8 mm (2.38 to 2.39 in.)
-
E
-
46.5 to 46.7 mm (1.83 to 1.84 in.) / 64.4 to 64.6 mm (2.535 to 2.543 in.)
-
F
55.0 to 55.2 mm (2.165 to 2.173 in.) / 68.8 to 69.3 mm (2.71 to 2.73 in.)
54.6 to 54.8 mm (2.15 to 2.16 in.) / 70.0 to 70.5 mm (2.76 to 2.78 in.)
-
G
-
65.4 to 65.6 mm (2.57 to 2.58 in.) / 85.6 to 86.0 mm (3.37 to 3.39 in.)
62.9 to 63.1 mm (2.476 to 2.484 in.) / 82.3 to 82.6 mm (3.24 to 3.25 in.)
H
39.5 to 39.8 mm (1.56 to 1.57 in.) / 56.9 to 57.2 mm (2.24 to 2.25 in.)
36.5 to 36.6 mm (1.437 to 1.441 in.) / 56.8 to 57.1 mm (2.24 to 2.25 in.)
36.5 to 36.7 mm (1.437 to 1.445 in.) / 56.7 to 57.2 mm (2.23 to 2.25 in.)
I
21.1 to 21.3 mm (0.831 to 0.839 in.) / 39.9 to 40.1 mm (1.57 to 1.58 in.)
23.0 to 23.3 mm (0.906 to 0.917 in.) / 44.0 to 44.2 mm (1.73 to 1.74 in.)
-
J
-
43.6 to 43.9 mm (1.72 to 1.73 in.) / 63.0 to 63.2 mm (2.48 to 2.49 in.)
47.2 to 47.4 mm (1.86 to 1.87 in.) / 67.1 to 67.4 mm (2.64 to 2.65 in.)


2. INSTALL 1ST AND REVERSE BRAKE PISTON


C161741E01
  1. Coat 3 new O-rings with ATF, and install them to the 1st and reverse brake piston.



    C162579E01
  1. Install the 1st and reverse brake piston to the transmission case.

    NOTICE:
    1. Be careful not to damage the O-ring.
    2. Make sure that the parking hole of the brake piston is on the bottom side by engaging the brake piston's protrusion to the transmission case's spline grooves.


3. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C162152E01
  1. Place the brake return spring onto the 1st and reverse brake piston.

    SST
    09380-60010   (09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-05040, 09381-05050)
  1. Place SST on the spring retainer, and compress the return spring.

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)


4. SELECT NO. 4 BRAKE FLANGE


C162577E01
  1. Measure distance A (from the tip of the 1st and reverse brake piston to the step in the transmission case) in the illustration. *1

    HINT:
    Standard distance A: 27.82 to 28.42 mm (1.09 to 1.12 in.)


    C162578E01
  1. Assemble the No. 4 brake flange, 7 No. 4 brake discs and 6 No. 4 brake plates, and measure distance B in the illustration. *2

    HINT:
    Standard distance B: 25.98 to 27.01 mm (1.02 to 1.06 in.)
  1. Measure length H of the No. 4 brake selective flange in the illustration.



  1. Apply the A and B measurements taken in *1 and *2 to the graph below. Use A for the X axis and B for the Y axis, and then choose the flange indicated by the graph point.

    HINT:
    Make sure that when the B measurement and selected flange's H dimension are subtracted from the A measurement, the value is 0.961 to 1.261 mm (0.0378 to 0.0495 in.).


    C162735E01

    No. 4 brake selective flange length H:
    Mark
    Thickness
    0
    0 mm (0 in.)
    2
    0.15 to 0.25 mm (0.00590 to 0.00984 in.)
    4
    0.35 to 0.45 mm (0.0138 to 0.0177 in.)
    6
    0.55 to 0.65 mm (0.0217 to 0.0256 in.)
    8
    0.75 to 0.85 mm (0.0295 to 0.0335 in.)
    10
    0.95 to 1.05 mm (0.0374 to 0.0413 in.)


5. INSTALL REAR PLANETARY GEAR ASSEMBLY


C161739E01
  1. Install the thrust bearing race.

    HINT:
    Use a small amount of MP grease to make the thrust bearing race stay securely in place.

    Bearing race diameter:
    Item
    Inside
    Outside
    Race J
    47.2 to 47.4 mm (1.86 to 1.87 in.)
    67.1 to 67.4 mm (2.64 to 2.65 in.)


    C162772E01
  1. Install the 2 thrust needle roller bearings to the rear planetary gear.

    Bearing diameter:
    Item
    Inside
    Outside
    Bearing I
    23.0 to 23.3 mm (0.906 to 0.917 in.)
    44.0 to 44.2 mm (1.73 to 1.74 in.)
    Bearing J
    43.6 to 43.9 mm (1.72 to 1.73 in.)
    63.0 to 63.2 mm (2.48 to 2.49 in.)

    HINT:
    Use a small amount of MP grease to make the thrust bearing stay securely in place.


    C162771
  1. Install the rear planetary gear assembly.



6. INSTALL BRAKE PLATE STOPPER SPRING


C162150


7. INSTALL REAR PLANETARY RING GEAR


C161734
  1. Install the rear planetary ring gear flange on the rear planetary ring gear.

  1. Using a screwdriver, install the snap ring.



    C161733E02
  1. Install the 3 thrust bearing races, thrust needle roller bearing and planetary ring gear with the rear planetary ring gear flange to the intermediate shaft.

    HINT:
    Use a small amount of MP grease to make the thrust bearing and race stay securely in place.

    Bearing and race diameter:
    Item
    Inside
    Outside
    Front race H
    39.5 to 39.8 mm (1.56 to 1.57 in.)
    56.9 to 57.2 mm (2.24 to 2.25 in.)
    Bearing H
    36.5 to 36.6 mm (1.437 to 1.441 in.)
    56.8 to 57.1 mm (2.24 to 2.25 in.)
    Rear race H
    36.5 to 36.7 mm (1.437 to 1.445 in.)
    56.7 to 57.2 mm (2.23 to 2.25 in.)
    Race I
    21.1 to 21.3 mm (0.831 to 0.839 in.)
    39.9 to 40.1 mm (1.57 to 1.58 in.)


8. INSTALL INTERMEDIATE SHAFT WITH REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR


C163074
  1. Install the intermediate shaft with rear planetary ring gear flange and rear planetary ring gear to the transmission case.



9. INSTALL NO. 4 BRAKE DISC


C161736E01
  1. Install the flange, 7 discs, 6 plates and selected flange.

    Install in order:
    F - D - P - D - P - D - P - D - P - D - P - D - P - D - S/F

    HINT:
    F = Flange
    D = Disc
    P = Plate
    S/F = Selected flange

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


10. INSTALL NO. 3 1-WAY CLUTCH INNER RACE


C162580E01
  1. Install the 1-way clutch inner race to the No. 3 1-way clutch assembly.

    NOTICE:
    Do not mistake the direction of the 1-way clutch inner race.


11. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY


C161748E01
  1. Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.



12. INSTALL NO. 3 1-WAY CLUTCH ASSEMBLY


C163075
  1. Install the 1-way clutch assembly to the transmission case.



    C161730E01
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07060)


13. INSTALL NO. 2 BRAKE PISTON


C162730E02
  1. Coat 2 new O-rings with ATF, and install them to the brake piston.

  1. Press the brake piston into the brake cylinder with both hands.

    NOTICE:
    Be careful not to damage the O-rings.


14. INSTALL NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON


    C161728
  1. Install the No. 2 brake cylinder with piston to the transmission case.

    NOTICE:

    1. C161729
    2. When installing the No. 2 brake cylinder with piston to the transmission case, align and install the cylinder's claw to the case's top groove.
    3. Make sure the No. 2 brake cylinder with piston is securely inserted into the transmission case.


15. SELECT NO. 2 BRAKE FLANGE


C162561E01
  1. Install the No. 2 brake piston return spring and flange on the No. 2 brake piston.

  1. Place SST on the brake flange and compress the brake return spring.

    SST
    09380-60010   (09381-06010, 09381-06020, 09381-06050, 09381-06070, 09381-06090, 09381-06120)
  1. Using a screwdriver, install the snap ring to the transmission case.



    C162575E01
  1. Measure distance A (from the top surface of the snap ring to the bottom surface of the brake piston return spring retainer) in the illustration. *1

    HINT:
    Standard distance A: 21.00 to 21.76 mm (0.834 to 0.857 in.)


    C162576E01
  1. Assemble the 4 discs, 3 plates and flange as shown in the illustration. Then with a fixture of 165.2 mm (6.50 in.) or less placed on the flange, measure distance B. *2

    HINT:
    Standard distance B: 16.54 to 17.15 mm (0.651 to 0.675 in.)


  1. Apply the A and B measurements taken in *1 and *2 to the graph below. Use A for the X axis and B for the Y axis, and then choose the flange indicated by the graph point.


    C162734E02

    HINT:
    Make sure that when the B measurement and selected flange's thickness are subtracted from the A measurement, the value is 2.20 to 2.50 mm (0.0866 to 0.0984 in.).

    Flange thickness:
    Mark
    Thickness
    0
    1.95 to 2.05 mm (0.0768 to 0.0807 in.)
    1
    2.05 to 2.15 mm (0.0807 to 0.0846 in.)
    2
    2.15 to 2.25 mm (0.0846 to 0.0886 in.)
    3
    2.25 to 2.35 mm (0.0886 to 0.0925 in.)
    4
    2.35 to 2.45 mm (0.0925 to 0.0965 in.)
    5
    2.45 to 2.55 mm (0.0965 to 0.100 in.)
    6
    2.55 to 2.65 mm (0.100 to 0.104 in.)
    7
    2.65 to 2.75 mm (0.104 to 0.108 in.)
  1. Remove the snap ring, flange and No. 2 brake piston return spring from the transmission case.



16. INSTALL NO. 2 BRAKE DISC SET


C161726E01
  1. Install the brake piston return spring, selective flange, 4 discs, 3 plates, and flange.

    Install in order:
    S/F - D - P - D - P - D - P - D - F

    HINT:
    S/F = Selective flange
    D = Disc
    P = Plate
    F = Flange

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


    C162561E01
  1. Place SST on the brake flange and compress the brake return spring.

    SST
    09380-60010   (09381-06010, 09381-06020, 09381-06050, 09381-06070, 09381-06090, 09381-06120)
  1. Using a screwdriver, install the snap ring to the transmission case.



17. INSTALL CENTER PLANETARY GEAR ASSEMBLY


C164079E01
  1. Install the center planetary sun gear and center planetary gear to the transmission case.

    NOTICE:
    Make sure to install the center planetary sun gear with the groove facing the transmission case.


18. INSTALL NO. 1 BRAKE PISTON


C162732E02
  1. Coat 2 new O-rings with ATF, and install them on the brake piston.

  1. Press the brake piston into the brake cylinder with both hands.

    NOTICE:
    Be careful not to damage the O-rings.


19. INSTALL NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON


    C161723
  1. Install the No. 1 brake cylinder with piston and brake piston return spring to the transmission case.

    NOTICE:

    1. C162731E01
    2. When installing the No. 1 brake cylinder with piston to the transmission case, align and install the cylinder's claw to the case's top groove.
    3. Make sure the No. 1 brake cylinder with piston is securely inserted into the transmission case.


    C162153E01
  1. Place SST on the brake return spring and compress the brake return spring.

    SST
    09380-60010   (09381-06010, 09381-06020, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120)
  1. Using a screwdriver, install the snap ring to the transmission case.



20. SELECT NO. 1 BRAKE FLANGE


C162573E01
  1. Measure distance A (from the step in the transmission case to the tip of the No. 1 brake piston) in the illustration. *1

    HINT:
    Standard distance A: 19.74 to 20.22 mm (0.777 to 0.796 in.)


    C162574E01
  1. Assemble the 4 plates and 4 discs and measure distance B in the illustration. *2

    HINT:
    Standard distance B: 16.72 to 17.19 mm (0.658 to 0.677 in.)


  1. Apply the A and B measurements taken in *1 and *2 to the graph below. Use A for the X axis and B for the Y axis, and then choose the flange indicated by the graph point.


    C162733E01

    HINT:
    Make sure that when the B measurement and selected flange's thickness are subtracted from the A measurement, the value is 0.56 to 0.86 mm (0.0220 to 0.0339 in.).

    Flange thickness:
    Mark
    Thickness
    0
    1.95 to 2.05 mm (0.0768 to 0.0807 in.)
    1
    2.15 to 2.25 mm (0.0846 to 0.0886 in.)
    2
    2.35 to 2.45 mm (0.0925 to 0.0965 in.)
    3
    2.55 to 2.65 mm (0.100 to 0.104 in.)


21. INSTALL CENTER PLANETARY RING GEAR


C161720
  1. Install the front planetary ring gear flange to the center planetary ring gear.



    C161719
  1. Using a screwdriver, install the snap ring.



22. INSTALL FRONT PLANETARY RING GEAR


C161718
  1. Install the front planetary ring gear to the center planetary ring gear.



23. INSTALL FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY AND CENTER PLANETARY RING GEAR


C161716E01
  1. Install the thrust bearing race and thrust needle roller bearing.

    HINT:
    Use a small amount of MP grease to make the thrust bearing and race stay securely in place.

    Bearing and race diameter:
    Item
    Inside
    Outside
    Race
    65.4 to 65.6 mm (2.57 to 2.58 in.)
    85.6 to 86.0 mm (3.37 to 3.39 in.)
    Bearing
    62.9 to 63.1 mm (2.476 to 2.484 in.)
    82.3 to 82.6 mm (3.24 to 3.25 in.)
  1. Install the front planetary ring gear with the front planetary ring gear flange and center planetary ring gear to the transmission case.



24. INSTALL FRONT PLANETARY GEAR ASSEMBLY


C163097
  1. Install the No. 2 planetary carrier thrust washer to the front planetary gear.

    HINT:
    Use a small amount of MP grease to make the thrust washer stay securely in place.

    Bearing race diameter:
    Item
    Inside
    Outside
    Race
    55.0 to 55.2 mm (2.165 to 2.173 in.)
    68.8 to 69.3 mm (2.71 to 2.73 in.)


    C163096E01
  1. Install the thrust needle roller bearing, thrust bearing race, front planetary sun gear and front planetary gear.

    HINT:
    Use a small amount of MP grease to make the thrust bearing and race stay securely in place.

    Bearing diameter:
    Item
    Inside
    Outside
    Bearing
    54.6 to 54.8 mm (2.15 to 2.16 in.)
    70.0 to 70.5 mm (2.76 to 2.78 in.)
    Race
    55.0 to 55.2 mm (2.165 to 2.173 in.)
    68.8 to 69.3 mm (2.71 to 2.73 in.)


25. INSTALL 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY


C161711
  1. Apply the No. 1 planetary carrier thrust washer to the 1-way clutch inner race, and then install them to the 1-way clutch.

    HINT:
    Use a small amount of MP grease to make the thrust washer stay securely in place.


26. INSPECT 1-WAY CLUTCH ASSEMBLY


C161775E01
  1. Install the 1-way clutch to the 1-way clutch inner race.

  1. Hold the 1-way clutch inner race and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.

  1. Remove the 1-way clutch from the 1-way clutch inner race.



27. INSTALL 1-WAY CLUTCH ASSEMBLY WITH 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY


C161710
  1. Install the 1-way clutch with 1-way clutch inner race to the transmission case.



28. INSTALL NO. 1 BRAKE DISC SET


C161721E01
  1. Install the 4 plates, 4 discs and flange.

    Install in order:
    P - D - P - D - P - D - P - D - F

    HINT:
    P = Plate
    D = Disc
    F = Flange

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


29. INSTALL NO. 3 BRAKE PISTON


C161713E02
  1. Coat 2 new O-rings with ATF, and install them to the brake piston.

  1. Press the brake piston into the brake cylinder with both hands.

    NOTICE:
    Be careful not to damage the O-rings.


    C162151E01
  1. Using SST and a press, compress the return spring and install the snap ring with a screwdriver.

    SST
    09380-60010   (09381-06020, 09381-06040, 09381-06060, 09381-06100, 09381-06110)

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.


30. INSTALL NO. 3 BRAKE CYLINDER WITH NO. 3 BRAKE PISTON AND NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C161709
  1. Install the No. 3 brake cylinder with the No. 3 brake piston and No. 3 brake piston return spring to the transmission case.

    NOTICE:

    1. C163076E01
      Align the oil holes of the No. 3 brake cylinder and transmission case as shown in the illustration.
    2. Make sure the No. 3 brake piston and cylinder are securely inserted into the transmission case.


31. INSTALL NO. 3 BRAKE PISTON HOLE SNAP RING


C161708E01
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07060)


32. INSTALL NO. 3 BRAKE DISC SET


C161707E01
  1. Install the ''O'' mark flange, 4 discs, 3 plates and ''A'' mark flange to the transmission case.

    Install in order:
    OF - D - P - D - P - D - P - D - AF

    HINT:
    OF = ''O'' mark flange
    P = Plate
    D = Disc
    AF = ''A'' mark flange

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


33. INSTALL NO. 3 BRAKE SNAP RING


C161635
  1. Using a screwdriver, install the snap ring.



34. INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY


    C161812E01
  1. Coat 2 new O-rings with ATF, and install them to the direct clutch piston.



    C161706
  1. Install the direct clutch return spring and No. 2 clutch balancer to the direct clutch piston.



    C162736
  1. Press the direct clutch piston with clutch return spring and clutch balancer into the reverse clutch piston with both hands.

    NOTICE:
    Be careful not to damage the O-ring.


    C161704E01
  1. Place SST on the direct clutch balancer, and compress the return spring with a press.

    SST
    09380-60010   (09381-06030, 09381-06040, 09381-06080)

    NOTICE:
    Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)

    NOTICE:
    Do not expand the snap ring excessively.


    D028536E07
  1. Set the end gap of the snap ring in the balancer as shown in the illustration.

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.


35. INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY


C161703E01
  1. Coat a new O-ring with ATF, and install it to the clutch drum.



    C161702E01
  1. Coat a new O-ring with ATF, and install it on the reverse clutch piston.



    C161701
  1. Pass the clutch drum into the reverse clutch piston with both hands.

    NOTICE:
    1. Be careful not to damage the O-ring.
    2. Make sure to align the holes of the reverse clutch piston and clutch drum as shown in the illustration.
    3. Make sure to align the protrusions of the reverse clutch pistons and the cutout of the clutch drum.


36. INSTALL NO. 3 CLUTCH BALANCER


C161657E01
  1. Coat a new O-ring with ATF, and install it to the reverse clutch piston.

  1. Install the reverse clutch return spring and balancer onto the reverse clutch piston.



    C161656E01
  1. Place SST on the clutch balancer, and compress the clutch balancer with a press.

    SST
    09380-60010   (09381-06020, 09381-06030, 09381-06040, 09381-06050, 09381-06070, 09381-06080)

    NOTICE:
    Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)

    NOTICE:
    Do not expand the snap ring excessively.


    C162738
  1. Set the end gap of the snap ring in the piston as shown in the illustration.

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.


37. INSTALL DIRECT CLUTCH DISC


C161655E01
  1. Place the oil pump onto the torque converter clutch, and then place the clutch drum.

  1. Install the 5 plates, 5 discs and reverse clutch flange on the clutch drum.

    Install in order:
    P - D - P - D - P - D - P - D - P - D - F

    HINT:
    P = Plate
    D = Disc
    F = Flange

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


    C162740
  1. Using a screwdriver, install the snap ring to the clutch drum.



  1. Using a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while blowing compressed air (392 kPa, 2.0 kgf/cm2, 57 psi) from the oil hole as shown in the illustration. Then choose from the 9 flange thicknesses in the table so that the measured value is within the standard value.

    Standard moving distance (A):
    0.58 to 0.88 mm (0.0228 to 0.0346 in.)


    C162571E01

    Flange thickness:
    Mark
    Thickness
    0
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    1
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    2
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    3
    3.75 to 3.85 mm (0.148 to 0.152 in.)
    4
    3.85 to 3.95 mm (0.152 to 0.156 in.)
    5
    3.95 to 4.05 mm (0.156 to 0.159 in.)
    6
    4.05 to 4.15 mm (0.159 to 0.163 in.)
    7
    4.15 to 4.25 mm (0.163 to 0.167 in.)
    8
    4.25 to 4.35 mm (0.167 to 0.171 in.)
  1. Temporarily remove the snap ring, attach the selected flange and reinstall the snap ring.



38. SELECT REVERSE CLUTCH FLANGE


C162741
  1. Using a screwdriver, install the snap ring to the clutch drum.

    NOTICE:
    Make sure to install the direct clutch and reverse clutch snap rings so that their openings face opposite directions.


    C162742E01
  1. Install the flange, 5 discs, 4 plates, selective flange and reverse clutch reaction sleeve to the clutch drum.

    Install in order:
    F - D - P - D - P - D - P - D - P - D - S/F

    HINT:
    F = Flange
    D = Disc
    P = Plate
    S/F = Selective flange


    C162743
  1. Using a screwdriver, install the hole snap ring.



  1. Using a dial indicator, measure the moving distance (A minus B) of the tip of the reverse clutch piston (A) and clutch flange at both ends across the diameter (B) while blowing compressed air (392 kPa, 2.0 kgf/cm2, 57 psi) from the oil hole as shown in the illustration. Then choose from the 12 flange thicknesses in the table so that the measured value is within the standard value.


    C162572E01

    Standard moving distance (A minus B):
    0.79 to 1.09 mm (0.0311 to 0.0429 in.)

    Flange thickness:
    Mark
    Thickness
    0
    2.35 to 2.45 mm (0.0925 to 0.0965 in.)
    1
    2.45 to 2.55 mm (0.0965 to 0.100 in.)
    2
    2.55 to 2.65 mm (0.100 to 0.104 in.)
    3
    2.65 to 2.75 mm (0.104 to 0.108 in.)
    4
    2.75 to 2.85 mm (0.108 to 0.112 in.)
    5
    2.85 to 2.95 mm (0.112 to 0.116 in.)
    6
    2.95 to 3.05 mm (0.116 to 0.120 in.)
    7
    3.05 to 3.15 mm (0.120 to 0.124 in.)
    8
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    A
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    B
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    C
    3.45 to 3.55 mm (0.136 to 0.140 in.)


    D029843E01
  1. Remove the snap ring, reverse clutch reaction sleeve and rear clutch disc set from the clutch drum.



39. INSTALL FORWARD CLUTCH PISTON SUB-ASSEMBLY AND COAST CLUTCH PISTON


C162744E01
  1. Coat a new O-ring with ATF, and install it to the input shaft.



    C162745
  1. Install the forward clutch piston and coast clutch piston to the input shaft.



    C161652E01
  1. Coat a new O-ring with ATF, and install it to the No. 1 clutch balancer.



    C161651
  1. Install the forward clutch return spring and No. 1 clutch balancer to the input shaft.

    NOTICE:
    Be careful not to damage the O-rings.


    C161650E01
  1. Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

    SST
    09350-30020   (09350-07040)

    NOTICE:
    Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)

    NOTICE:
    Do not expand the snap ring excessively.


    C162759E01
  1. Set the end gap of the snap ring in the balancer as shown in the illustration.

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.


40. INSTALL COAST CLUTCH DISC SET


C162747E01
  1. Install the 4 plates, 4 discs and flange.

    Install in order:
    P - D - P - D - P - D - P - D - F

    HINT:
    P = Plate
    D = Disc
    F = Flange

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


    C162748
  1. Temporarily install the snap ring.



    C162569E01
  1. Using a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while blowing compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) from the oil hole as shown in the illustration. Then choose from the 11 flange thicknesses in the table so that the measured value is within the standard value.

    Standard moving distance (A):
    0.41 to 0.71 mm (0.0161 to 0.0280 in.)

    Flange thickness:
    Mark
    Thickness
    0
    2.95 to 3.05 mm (0.116 to 0.120 in.)
    1
    3.05 to 3.15 mm (0.120 to 0.124 in.)
    2
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    3
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    4
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    5
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    6
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    7
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    8
    3.75 to 3.85 mm (0.148 to 0.152 in.)
    A
    3.85 to 3.95 mm (0.152 to 0.156 in.)
    B
    3.95 to 4.05 mm (0.156 to 0.159 in.)
  1. Temporarily remove the snap ring, attach the selected flange and reinstall the snap ring.



41. INSTALL NO. 4 1-WAY CLUTCH ASSEMBLY


C161643
  1. Install the No. 2 clutch hub thrust washer to the coast clutch hub.

    HINT:
    Use a small amount of MP grease to make the thrust washer stay securely in place.
  1. Install the 1-way clutch to the coast clutch hub.



42. INSPECT NO. 4 1-WAY CLUTCH ASSEMBLY


C161784E01
  1. Hold the coast clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.



43. INSTALL COAST CLUTCH HUB SUB-ASSEMBLY WITH NO. 4 1-WAY CLUTCH ASSEMBLY


C163077E01
  1. Install the 2 thrust needle roller bearings, thrust bearing race and coast clutch hub with the No. 4 1-way clutch to the clutch drum.

    HINT:
    Use a small amount of MP grease to make the thrust bearing and race stay securely in place.

    Bearing and race diameter:
    Item
    Inside
    Outside
    Bearing C
    21.1 to 21.3 mm (0.831 to 0.839 in.)
    39.5 to 39.8 mm (1.56 to 1.57 in.)
    Race
    22.8 to 23.1 mm (0.898 to 0.909 in.)
    44.5 to 44.8 mm (1.75 to 1.76 in.)
    Bearing D
    39.5 to 39.7 mm (1.555 to 1.563 in.)
    60.5 to 60.8 mm (2.38 to 2.39 in.)


44. INSTALL FORWARD MULTIPLE DISC CLUTCH DISC SET


C163078E01
  1. Install the cushion, 6 plates, 6 discs and flange to the input shaft.

    Install in order:
    C - P - D - P - D - P - D - P - D - P - D - P - D - F

    HINT:
    C = Cushion
    P = Plate
    D = Disc
    F = Flange

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


    D028519E01
  1. Temporarily install the snap ring.



    C162570E01
  1. Using a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while blowing compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) from the oil hole as shown in the illustration. Then choose from the 12 flange thicknesses in the table so that the measured value is within the standard value.

    Standard moving distance (A):
    0.85 to 1.15 mm (0.0335 to 0.0453 in.)

    Flange thickness:
    Mark
    Thickness
    0
    2.95 to 3.05 mm (0.116 to 0.120 in.)
    1
    3.05 to 3.15 mm (0.120 to 0.124 in.)
    2
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    3
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    4
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    5
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    6
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    7
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    8
    3.75 to 3.85 mm (0.148 to 0.152 in.)
    A
    3.85 to 3.95 mm (0.152 to 0.156 in.)
    B
    3.95 to 4.05 mm (0.156 to 0.159 in.)
    C
    4.05 to 4.15 mm (0.159 to 0.163 in.)
  1. Temporarily remove the snap ring, attach the selected flange and reinstall the snap ring.



45. INSTALL INPUT SHAFT OIL SEAL RING


C162568E01
  1. Overlap the seal ring edges in the axial direction.

    NOTICE:
    1. Overlapping the seal ring edges in the axial direction prevents damage to the seal ring.
    2. Do not overlap the seal ring edges in the radial direction, as this may damage the seal ring.


    C161649E01
  1. Coat 4 new oil seal rings with ATF.

  1. Squeeze the ends of the 4 oil seal rings together, and then install them to the input shaft groove.

    NOTICE:
    Do not excessively widen the rings.

    HINT:
    After installing the oil seal rings, check that they rotate smoothly.


46. INSTALL INPUT SHAFT ASSEMBLY


C161648
  1. Install the input shaft to the clutch drum.



47. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY


C161641
  1. Install the No. 3 clutch hub thrust washer, forward clutch hub and thrust needle roller bearing to the clutch drum.

    NOTICE:
    Before installing the forward clutch hub, apply ATF to the forward clutch hub bush's sliding surfaces. After the installation, check that the forward clutch hub rotates smoothly.

    HINT:
    Use a small amount of MP grease to make the thrust bearing and thrust washer stay securely in place.

    Bearing diameter:
    Item
    Inside
    Outside
    Bearing
    46.5 to 46.7 mm (1.83 to 1.84 in.)
    64.4 to 64.6 mm (2.535 to 2.543 in.)


48. INSTALL REVERSE CLUTCH HUB SUB-ASSEMBLY


C162750
  1. Install the reverse clutch hub to the clutch drum.

    NOTICE:
    Before installing the reverse clutch hub, apply ATF to the reverse clutch hub bush's sliding surfaces. After the installation, check that the reverse clutch rotates smoothly.


49. INSTALL REAR CLUTCH DISC SET


C162751E01
  1. Install the flange, 5 discs, 4 plates, selected flange and reverse clutch reaction sleeve to the clutch drum.

    Install in order:
    F - D - P - D - P - D - P - D - P - D - S/F

    HINT:
    F = Flange
    D = Disc
    P = Plate
    S/F = Selected flange
  1. Using a screwdriver, install the snap ring to the clutch drum.



50. INSTALL NO. 2 1-WAY CLUTCH ASSEMBLY


C161634
  1. Install the clutch drum thrust washer to the clutch drum.

    HINT:
    Use a small amount of MP grease to make the thrust washer stay securely in place.
  1. Install the 1-way clutch to the clutch drum.



51. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY


C161779E01
  1. Hold the reverse clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.



52. INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


C161633E01
  1. Install the 2 thrust needle roller bearings.

    HINT:
    Use a small amount of MP grease to make the thrust bearing stay securely in place.

    Bearing diameter:
    Item
    Inside
    Outside
    Bearing A
    72.0 to 72.3 mm (2.83 to 2.85 in.)
    85.3 to 85.6 mm (3.36 to 3.37 in.)
    Bearing B
    36.5 to 36.7 mm (1.437 to 1.445 in.)
    52.9 to 53.2 mm (2.08 to 2.09 in.)
  1. Coat the clutch drum thrust washer with petroleum jelly and install it onto the clutch drum and input shaft assembly.



    C164078
  1. Install the clutch drum and input shaft drum assembly onto the transmission case.



53. INSTALL OIL PUMP ASSEMBLY


C161631E01
  1. Coat a new O-ring with ATF, and install it to the oil pump.

  1. Install the 2 thrust bearing races to the front oil pump.

    Thrust bearing race diameter:
    Item
    Inside
    Outside
    Race A
    74.3 to 74.6 mm (2.93 to 2.94 in.)
    87.4 to 87.7 mm (3.44 to 3.45 in.)
    Race B
    38.0 to 38.3 mm (1.50 to 1.51 in.)
    53.9 to 54.1 mm (2.12 to 2.13 in.)


    C161629
  1. Pass the input shaft through the center hole of the oil pump, and align the bolt holes of the oil pump assembly with the transmission case.

  1. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.

  1. Apply seal packing to the flanges of the bolts.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Do not allow seal packing to contact the bolts' threads.
  1. Install the 10 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    During installation, do not allow oil to contact the bolts or the surface of the oil pump body.


54. INSPECT INDIVIDUAL PISTON OPERATION


C161780E01
  1. Check the operating sound while applying compressed air into the oil holes indicated in the illustration.

    HINT:
    When inspecting the direct clutch, check with the C3 accumulator piston holes indicated in the illustration.
    If there is no sound, disassemble and check the installation condition of the parts.
    1. No. 2 clutch (C2)
    2. No. 3 clutch (C3)
    3. No. 4 clutch (C4)
    4. No. 1 clutch (C1)
    5. No. 3 brake (B3)
    6. No. 1 brake (B1)
    7. No. 2 brake (B2)
    8. No. 4 brake (B4)


55. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL


C161808E01
  1. Using SST, tap in 2 new oil seals.

    SST
    09350-30020   (09350-07110)
  1. Coat the lips of the oil seals with MP grease.



56. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY


C161809E01
  1. Install a new spacer to the manual valve lever.

  1. Push the manual valve lever shaft through the transmission case, and install the manual valve lever to the shaft.



    C161627
  1. Using a hammer, tap in a new spring pin.



    C161810
  1. Align the manual valve lever indentation with the spacer hole, and stake them together with the punch.

  1. Check that the shaft rotates smoothly.



57. INSTALL PARKING LOCK PAWL


C161624E02
  1. Install a new E-ring to the shaft.

  1. Install the parking lock pawl, shaft and spring.



58. INSTALL PARKING LOCK ROD SUB-ASSEMBLY


C161623E01
  1. Connect the parking lock rod to the manual valve lever.



59. INSTALL PARKING LOCK PAWL BRACKET


C161622
  1. Place the parking lock pawl bracket onto the transmission case and install the 3 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


    C162752E01
  1. Move the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked by the lock pawl.



60. INSTALL B-1 ACCUMULATOR VALVE


C162753
  1. Install the 2 springs and accumulator valve to the hole.

    Spring diameter:
    Spring
    Free length
    Outer diameter
    Color
    B-1 Inner
    44.98 mm (1.77 in.)
    11.30 mm (0.445 in.)
    Natural
    B-1 Outer
    46.36 mm (1.83 in.)
    17.10 mm (0.673 in.)
    Natural


61. INSTALL C-3 ACCUMULATOR PISTON


C162754E01
  1. Coat 2 new O-rings with ATF, and install them to the piston.

  1. Install the spring and accumulator piston to the hole.

    Spring diameter:
    Spring
    Free length
    Outer diameter
    Color
    C-3
    73.35 mm (2.89 in.)
    19.9 mm (0.783 in.)
    Red


62. INSTALL B-3 ACCUMULATOR PISTON


C162755E01
  1. Coat 2 new O-rings with ATF, and install them to the piston.

  1. Install the spring and accumulator piston to the hole.

    Spring diameter:
    Spring
    Free length
    Outer diameter
    Color
    B-3
    64.50 mm (2.54 in.)
    19.5 mm (0.768 in.)
    Orange


63. INSTALL C-2 ACCUMULATOR PISTON


C162756E01
  1. Coat 2 new O-rings with ATF, and install them to the piston.

  1. Install the spring and accumulator piston to the hole.

    Spring diameter:
    Spring
    Free length
    Outer diameter
    Color
    C-2
    68.0 mm (2.68 in.)
    16.1 mm (0.634 in.)
    Light green


64. INSTALL CHECK BALL BODY


C161618E01
  1. Install the spring and check ball body.



65. INSTALL BRAKE DRUM GASKET


C161617E01
  1. Install 3 new brake drum gaskets.



66. INSTALL TRANSMISSION CASE GASKET


C161616E01
  1. Install 3 new transmission case gaskets.



67. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


C162146E01
  1. Align the hole of the manual valve with the pin of the lever.



    C162147E01
  1. Install the 19 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    36 mm (1.42 in.) for bolt A
    25 mm (0.984 in.) for bolt B
    45 mm (1.77 in.) for bolt C
    50 mm (1.97 in.) for bolt D
  1. Install the detent spring and detent spring cover with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


68. INSTALL TRANSMISSION WIRE


C161615E01
  1. Install 2 new O-rings to the transmission wires.



    C161614
  1. Install the transmission wire harnesses.

  1. Install the bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


    C161112E02
  1. Connect the 9 connectors to the solenoid valves.

  1. Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    12 mm (0.472 in.) for bolt A
    36 mm (1.42 in.) for bolt B


69. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


C161111
  1. Coat a new O-ring with ATF, and install it to the oil strainer.

  1. Install the oil strainer with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


70. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


C162564E01
  1. Install the 4 magnets.

  1. Install a new gasket on the oil pan.

  1. Install the 12 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

    NOTICE:

    1. C157303E01
    2. Make sure that there is no oil or foreign matter on the gasket seal surface and oil pan contact surface.
    3. Install the gasket so that there is no slack in the gasket, and make sure the seal surface's entire circumference is level.
    4. Make sure that the 9 gasket drop prevention protrusions are set on the oil pan.
    5. When tightening the oil pan, make sure that the gasket is not pinched between the gasket tightening area's sleeve and the transmission's seal surface.
  1. Install the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


71. INSTALL TRANSFER CASE ADAPTER RADIAL BALL BEARING


C162768E01
  1. Using SST and a press, press in the bearing.

    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07150)
  1. Using a screwdriver, install the snap ring.



72. INSTALL TRANSMISSION CASE ADAPTER OIL SEAL


C162769E01
  1. Coat the lip of a new oil seal with ATF.

  1. Using SST and a hammer, tap in the oil seal.

    Standard depth:
    0 to 0.1 mm (0 to 0.00394 in.)
    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07150)


73. INSTALL TRANSFER ADAPTER REAR


C161783E01
  1. Clean the threads of the bolts and case with non-residue solvent.

  1. Apply seal packing to the rear adaptor transfer.

    Seal packing:
    Toyota Genuine Seal Packing 1281,
    Three Bond 1281 or equivalent

    Seal diameter:
    1.0 to 1.5 mm (0.0394 to 0.0591 in.)


    C162765
  1. Install the rear adaptor transfer with the 10 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }


74. INSTALL AUTOMATIC TRANSMISSION HOUSING


C159660
  1. Clean the threads of the bolts and case with non-residue solvent.

  1. Install the transmission housing with the 14 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }


75. INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE


C159659
  1. Coat a new O-ring with ATF and install it to the breather tube.

  1. Install the breather tube with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


76. INSTALL TRANSMISSION OIL COOLER ASSEMBLY


C161366E01
  1. w/ Trailer Towing System:

    1. Coat 4 new O-rings with ATF.

    2. Install the 4 O-rings, transmission oil cooler and transmission oil thermostat to the automatic transmission assembly with the 3 bolts.

      Torque:
      21 N*m{ 214 kgf*cm , 15 ft.*lbf }


    C161367E01
  1. w/o Trailer Towing System:

    1. Coat 4 new O-rings with ATF.

    2. Install the 4 O-rings, transmission oil cooler and transmission oil cooler spacer to the automatic transmission assembly with the 3 bolts.

      Torque:
      21 N*m{ 214 kgf*cm , 15 ft.*lbf }


77. INSTALL SPEED SENSOR


C159658
  1. Coat 2 new O-rings with ATF, and install them to the speed sensors.

  1. Install the 2 speed sensors.

  1. Install the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


78. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


C159656E01
  1. Install the park/neutral position switch to the manual valve lever shaft, and temporarily install the adjusting bolt.

  1. Install a new lock washer and the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }
  1. Temporarily install the control shaft lever RH.



    C155873E01
  1. Turn the control shaft lever RH counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.

  1. Remove the control shaft lever RH.



    D025795E10
  1. Align the groove with the neutral basic line.

  1. Hold the switch in position and tighten the bolt.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


    D027990E01
  1. Using a screwdriver, bend the tabs of the lock washer.



79. INSTALL TRANSMISSION CONTROL SHAFT LEVER RH


C155869
  1. Install the control shaft lever RH with the washer and nut.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }