AUTOMATIC TRANSMISSION UNIT > INSPECTION

for Preparation Click here



1. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


D001124E01

  1. Remove the magnets, and use them to collect steel particles.

  1. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear
    2. Brass (non-magnetic): bush wear


2. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY


D027993E03

  1. Hold the reverse clutch hub and turn the 1-way clutch assembly.

  1. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.
    If there is a problem with the 1- way clutch, replace the No. 2 1-way clutch assembly.



3. INSPECT REAR CLUTCH DISC


C162758

  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


4. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY


D028000E01

  1. Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.

    Standard inside diameter:
    35.812 to 35.837 mm (1.410 to 1.411 in.)

    Maximum inside diameter:
    35.887 mm (1.413 in.)
    1. If the inside diameter is more than the maximum, replace the reverse clutch hub.


5. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY


    D028501E01

  1. Using a dial indicator, measure the inside diameter of the forward clutch hub bush.

    Standard inside diameter:
    26.037 to 26. 062 mm (1.025 to 1.026 in.)

    Maximum inside diameter:
    26.112 mm (1.028 in.)
    1. If the inside diameter is more than the maximum, replace the forward clutch hub.


6. INSPECT UNDERDRIVE 1-WAY CLUTCH ASSEMBLY


C161784E01

  1. Hold the coast clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.
    If there is a problem with the 1-way clutch, replace the underdrive 1-way clutch assembly.



7. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC


C161790

  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


8. INSPECT COAST CLUTCH DISC


C161789

  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


9. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY


C161788

  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    26.74 mm (1.05 in.)
    If the free length is less than the standard, replace the forward clutch return spring sub-assembly.


10. INSPECT DIRECT CLUTCH DISC


C161787

  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


11. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


C161786

  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.04 mm (0.828 in.)
    If the free length is less than the standard, replace the reverse clutch return spring sub-assembly.


12. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY


C161785

  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.51 mm (0.768 in.)
    If the free length is less than the standard, replace the direct clutch return spring sub-assembly.


13. INSPECT NO. 3 BRAKE DISC


C161778

  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


14. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C171518

  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.72 mm (0.619 in.)
    If the free length is less than the standard, replace the No. 3 brake piston return spring sub-assembly.


15. INSPECT FRONT PLANETARY GEAR ASSEMBLY


D028544E01

  1. Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

    Standard clearance:
    0.2 to 0.60 mm (0.00787 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)
    1. If the clearance is more than the maximum, replace the front planetary gear assembly.


    D028543E01

  1. Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.

    Maximum inside diameter:
    57.48 mm (2.26 in.)
    1. If the inside diameter is more than the maximum, replace the front planetary gear.


16. INSPECT 1-WAY CLUTCH ASSEMBLY


D028542E03

  1. Install the 1-way clutch to the 1-way clutch inner race.

  1. Hold the 1-way clutch inner race and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.
    If there is a problem with the 1-way clutch, replace the 1-way clutch assembly.

  1. Remove the 1-way clutch from the 1-way clutch inner race.



17. INSPECT NO. 1 BRAKE DISC


C171514

  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


18. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


C171519

  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.05 mm (0.671 in.)
    If the free length is less than the standard, replace the brake piston return spring sub-assembly.


19. INSPECT NO. 2 BRAKE DISC


    C161770

  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


20. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C171520

  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.45 mm (0.687 in.)
    If the free length is less than the standard, replace the No. 2 brake piston return spring sub-assembly.


21. INSPECT CENTER PLANETARY GEAR ASSEMBLY


    D028533E01

  1. Using a feeler gauge, measure the center planetary gear pinion thrust clearance.

    Standard clearance:
    0.12 to 0.68 mm (0.00472 to 0.0268 in.)

    Maximum clearance:
    0.73 mm (0.0287 in.)
    1. If the clearance is more than the maximum, replace the center planetary gear assembly.


22. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY


D028532E03

  1. Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.
    If there is a problem with the 1-way clutch, replace the No. 3 1-way clutch assembly.



23. INSPECT REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY


    D028531E01

  1. Using a dial indicator, measure the inside diameter of the rear planetary ring gear bush.

    Maximum inside diameter:
    32.175 mm (1.27 in.)
    1. If the inside diameter is more than the maximum, replace the rear planetary ring gear.


24. INSPECT INTERMEDIATE SHAFT


    D028529E01

  1. Using a dial indicator, measure the intermediate shaft runout.

    Maximum runout:
    0.08 mm (0.00315 in.)
    If the runout is more than the maximum, replace the intermediate shaft with a new one.


    D028530E02

  1. Using a micrometer, check the outer diameter of the intermediate shaft at the positions shown in the diagram.

    Standard diameter:
    A, B:
    25.962 to 25.975 mm (1.022 to 1.023 in.)
    C, D:
    32.062 to 32.075 mm (1.262 to 1.263 in.)

    Minimum diameter:
    A, B:
    25.912 mm (1.02 in.)
    C, D:
    32.012 mm (1.26 in.)
    If the outer diameter is less than the minimum, replace the intermediate shaft with a new one.


25. INSPECT NO. 4 BRAKE DISC


    C161745

  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) the grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 15 minutes.


26. INSPECT REAR PLANETARY GEAR ASSEMBLY


C161743

  1. Using a feeler gauge, measure the rear planetary gear pinion thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00787 to 0.0236 in.)

    Maximum clearance:
    0.65 mm (0.0256 in.)
    1. If the clearance is more than the maximum, replace the planetary gear assembly.


    D028528E01

  1. Using a dial indicator, measure the inside diameter of the rear planetary gear bush.

    Maximum inside diameter:
    20.075 mm (0.790 in.)
    1. If the inside diameter is more than the maximum, replace the rear planetary gear assembly.


27. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


C171521

  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    23.74 mm (0.935 in.)
    If the free length is less than the standard, replace the 1st and reverse brake return spring sub-assembly.


28. INSPECT INDIVIDUAL PISTON OPERATION


    D031549E04

  1. Check the operating sound while applying compressed air into the oil holes indicated in the illustration.

    HINT:
    When inspecting the rear clutch, check the operating sound with the C3 accumulator piston hole closed.
    If there is no sound, disassemble and check the installation condition of the parts.
    1. Forward multiple disc clutch (C1)
    2. Direct clutch (C2)
    3. Rear clutch (C3)
    4. Coast clutch (C4)
    5. No. 1 brake (B1)
    6. No. 2 brake (B2)
    7. No. 3 brake (B3)
    8. No. 4 brake (B4)