DTC B1620/21 Driver Side - Side Airbag Sensor Circuit Malfunction |
DTC B1625/22 Front Passenger Side - Side Airbag Sensor Circuit Malfunction |
for Preparation Click here
DESCRIPTION
The side airbag sensor assembly LH consists of parts such as the safing sensor, the diagnostic circuit and the lateral deceleration sensor. The configuration of the side airbag sensor assembly RH is the same as that of the LH.When the airbag sensor assembly center receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1620/21 is set when a malfunction is detected in the side airbag sensor assembly (driver seat side) circuit.
DTC B1625/22 is set when a malfunction is detected in the side airbag sensor assembly (front passenger seat side) circuit.
DTC No. | DTC Detecting Conditions | Trouble Areas |
B1620/21 |
|
|
B1625/22 |
|
|
WIRING DIAGRAM
INSPECTION PROCEDURE
- NOTICE:
- In order to prevent unexpected airbag deployment, disconnect the following connectors before inspecting parts such as wire harnesses, if the application of tester probes to the center airbag sensor assembly connector is necessary.
- (a) Turn the ignition switch to the LOCK position.
- (b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
- (c) Disconnect the connectors from the center airbag sensor assembly.
- (d) Disconnect the connectors from the steering pad.
- (e) Disconnect the connector from the front passenger airbag assembly.
- (f) Disconnect the connector from the front seat airbag assembly LH.
- (g) Disconnect the connector from the front seat airbag assembly RH.
- HINT:
- Skip the following steps if side and curtain shield airbags are not fitted.
- (h) Disconnect the connector from the curtain shield airbag assembly LH.
- (i) Disconnect the connector from the curtain shield airbag assembly RH.
- (j) Disconnect the connector from the front seat outer belt assembly LH.
- (k) Disconnect the connector from the front seat outer belt assembly RH.
1.CHECK DTC |
Proceed to the appropriate step according to DTC readings.
Check the DTC (Click here).
- Result:
Result Proceed to DTC B1620/21 is output. A DTC B1625/22 is output. B DTC B1620/21 and B1625/22 are output. C Neither DTC B1620/21 nor B1625/22 is output. D
|
| ||||
|
| ||||
|
| ||||
A | |
2.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly LH.
- OK:
- The connectors are properly connected.
|
| ||||
OK | |
3.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly LH side) are not damaged (Click here).
- OK:
- The connectors are not deformed or damaged.
|
| ||||
OK | |
4.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
- SST
- 09843-18040
Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly LH.
Using SST, connect S11-4 (BBL+) and S11-3 (BBL-) of connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A22-8 (BBD+) - A22-15 (BBD-) Always Below 1 Ω
|
| ||||
OK | |
5.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
Disconnect the SST from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A22-8 (BBD+) - A22-15 (BBD-) Always 1 MΩ or Higher
|
| ||||
OK | |
6.CHECK NO. 2 FLOOR WIRE (TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
- Standard voltage:
Tester Connection Condition Specified Condition A22-8 (BBD+) - Body ground Ignition switch ON Below 1 V A22-15 (BBD-) - Body ground Ignition switch ON Below 1 V
|
| ||||
OK | |
7.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A22-8 (BBD+) - Body ground Always 1 MΩ or Higher A22-15 (BBD-) - Body ground Always 1 MΩ or Higher
|
| ||||
OK | |
8.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH |
Connect the connectors to the center airbag sensor assembly.
Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn any ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result Proceed to DTC B1620/21 is output. A DTC B1625/22 is output. B Neither DTC B1620/21 nor B1625/22 is output. C
|
| ||||
|
| ||||
A | |
9.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the rear airbag sensor LH.
- OK:
- The connectors are properly connected.
|
| ||||
OK | |
10.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly LH side and rear airbag sensor LH side) are not damaged (Click here).
- OK:
- The connectors are not deformed or damaged.
|
| ||||
OK | |
11.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
- SST
- 09843-18040
Disconnect the connectors from the side airbag sensor assembly LH and the rear airbag sensor LH.
Using SST, connect S13-1 (BCL-) and S13-2 (BCL+) of connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S11-1 (BCL+) - S11-2 (BCL-) Always Below 1 Ω
|
| ||||
OK | |
12.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
Disconnect the SST from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S11-1 (BCL+) - S11-2 (BCL-) Always 1 MΩ or Higher
|
| ||||
OK | |
13.CHECK NO. 2 FLOOR WIRE (TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
- Standard voltage:
Tester Connection Condition Specified Condition S11-1 (BCL+) - Body ground Ignition switch ON Below 1 V S11-2 (BCL-) - Body ground Ignition switch ON Below 1 V
|
| ||||
OK | |
14.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S11-1 (BCL+) - Body ground Always 1 MΩ or Higher S11-2 (BCL-) - Body ground Always 1 MΩ or Higher
|
| ||||
OK | |
15.CHECK DTC |
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1620/21 is not output.
- HINT:
- DTCs other than B1620/21 may be output at this time, but they are not related to this check.
|
| ||||
NG | |
16.REPLACE CENTER AIRBAG SENSOR ASSEMBLY |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
- HINT:
- Perform the inspection using parts from a normal vehicle when possible.
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- B1620/21 is not output.
- HINT:
- DTCs other than B1620/21 may be output at this time, but they are not related to this check.
|
| ||||
OK | ||
|
17.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.
- OK:
- The connectors are properly connected.
|
| ||||
OK | |
18.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly RH side) are not damaged (Click here).
- OK:
- The connectors are not deformed or damaged.
|
| ||||
OK | |
19.CHECK FLOOR WIRE (FOR OPEN) |
- SST
- 09843-18040
Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly RH.
Using SST, connect S12-4 (BBR+) and S12-3 (BBR-) of connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A23-8 (BBP+) - A23-11 (BBP-) Always Below 1 Ω
|
| ||||
OK | |
20.CHECK FLOOR WIRE (FOR SHORT) |
Disconnect the SST from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A23-8 (BBP+) - A23-11 (BBP-) Always 1 MΩ or Higher
|
| ||||
OK | |
21.CHECK FLOOR WIRE (TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
- Standard voltage:
Tester Connection Condition Specified Condition A23-8 (BBP+) - Body ground Ignition switch Below 1 V A23-11 (BBP-) - Body ground Ignition switch Below 1 V
|
| ||||
OK | |
22.CHECK FLOOR WIRE (TO GROUND) |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A23-8 (BBP+) - Body ground Always 1 MΩ or Higher A23-11 (BBP-) - Body ground Always 1 MΩ or Higher
|
| ||||
OK | |
23.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
Connect the connectors to the center airbag sensor assembly.
Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- Result:
Result Proceed to DTC B1625/22 is output. A DTC B1620/21 is output. B Neither DTC B1620/21 nor B1625/22 is output. C
|
| ||||
|
| ||||
A | |
24.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.
- OK:
- The connectors are properly connected.
|
| ||||
OK | |
25.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly RH side and rear airbag sensor RH side) are not damaged (Click here).
- OK:
- The connectors are not deformed or damaged.
|
| ||||
OK | |
26.CHECK FLOOR WIRE (FOR OPEN) |
- SST
- 09843-18040
Disconnect the connectors from the side airbag sensor assembly RH and the rear airbag sensor RH.
Using SST, connect S14-1 (BCR-) and S14-2 (BCR+) of connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S12-1 (BCR+) - S12-2 (BCR-) Always Below 1 Ω
|
| ||||
OK | |
27.CHECK FLOOR WIRE (FOR SHORT) |
Disconnect the SST from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S12-1 (BCR+) - S12-2 (BCR-) Always 1 MΩ or Higher
|
| ||||
OK | |
28.CHECK FLOOR WIRE (TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
- Standard resistance:
Tester Connection Condition Specified Condition S12-1 (BCR+) - Body ground Ignition switch ON Below 1 V S12-2 (BCR-) - Body ground Ignition switch ON Below 1 V
|
| ||||
OK | |
29.CHECK FLOOR WIRE (TO GROUND) |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S12-1 (BCR+) - Body ground Always 1 MΩ or Higher S12-2 (BCR-) - Body ground Always 1 MΩ or Higher
|
| ||||
OK | |
30.CHECK DTC |
Connect the connectors to the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1625/22 is not output.
- HINT:
- DTCs other than B1625/22 may be output at this time, but they are not related to this check.
|
| ||||
NG | |
31.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Replace the center airbag sensor assembly (Click here).
- HINT:
- Perform the inspection using parts from a normal vehicle when possible.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1625/22 is not output.
- HINT:
- DTCs other than B1625/22 may be output at this time, but they are not related to this check.
|
| ||||
OK | ||
|
32.CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly LH.
- OK:
- The connectors are properly connected.
|
| ||||
OK | |
33.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly LH side) are not damaged (Click here).
- OK:
- The connectors are not deformed or damaged.
|
| ||||
OK | |
34.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
- SST
- 09843-18040
Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly LH.
Using SST, connect S11-4 (BBL+) and S11-3 (BBL-) of connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A22-8 (BBD+) - A22-15 (BBD-) Always Below 1 Ω
|
| ||||
OK | |
35.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
Disconnect the SST from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A22-8 (BBD+) - A22-15 (BBD-) Always 1 MΩ or Higher
|
| ||||
OK | |
36.CHECK NO. 2 FLOOR WIRE (TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
- Standard voltage:
Tester Connection Condition Specified Condition A22-8 (BBD+) - Body ground Ignition switch ON Below 1 Ω A22-15 (BBD-) - Body ground Ignition switch ON Below 1 Ω
|
| ||||
OK | |
37.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A22-8 (BBD+) - Body ground Always 1 MΩ or Higher A22-15 (BBD-) - Body ground Always 1 MΩ or Higher
|
| ||||
OK | |
38.CHECK CONNECTION OF CONNECTORS |
Check that the connectors are properly connected to the rear airbag sensor LH.
- OK:
- The connectors are properly connected.
|
| ||||
OK | |
39.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly LH side and rear airbag sensor LH side) are not damaged (Click here).
- OK:
- The connectors are not deformed or damaged.
|
| ||||
OK | |
40.CHECK NO. 2 FLOOR WIRE (FOR OPEN) |
- SST
- 09843-18040
Disconnect the connectors from the side airbag sensor assembly LH and the rear airbag sensor LH.
Using SST, connect S13-1 (BCL-) and S13-2 (BCL+) of connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S11-1 (BCL+) - S11-2 (BCL-) Always Below 1 Ω
|
| ||||
OK | |
41.CHECK NO. 2 FLOOR WIRE (FOR SHORT) |
Disconnect the SST from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S11-1 (BCL+) - S11-2 (BCL-) Always 1 MΩ or Higher
|
| ||||
OK | |
42.CHECK NO. 2 FLOOR WIRE (TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
- Standard voltage:
Tester Connection Condition Specified Condition S11-1 (BCL+) - Body ground Ignition switch ON Below 1 Ω S11-2 (BCL-) - Body ground Ignition switch ON Below 1 Ω
|
| ||||
OK | |
43.CHECK NO. 2 FLOOR WIRE (TO GROUND) |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S11-1 (BCL+) - Body ground Always 1 MΩ or Higher S11-2 (BCL-) - Body ground Always 1 MΩ or Higher
|
| ||||
OK | |
44.CHECK CONNECTION OF CONNECTORS |
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.
- OK:
- The connectors are properly connected.
|
| ||||
OK | |
45.CHECK CONNECTORS |
Check that the connectors (on the center airbag sensor assembly side and side airbag sensor assembly RH side) are not damaged (Click here).
- OK:
- The connectors are not deformed or damaged.
|
| ||||
OK | |
46.CHECK FLOOR WIRE (FOR OPEN) |
- SST
- 09843-18040
Disconnect the connectors from the center airbag sensor assembly and the side airbag sensor assembly RH.
Using SST, connect S12-4 (BBR+) and S12-3 (BBR-) of connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A23-8 (BBP+) - A23-11 (BBP-) Always Below 1 Ω
|
| ||||
OK | |
47.CHECK FLOOR WIRE (FOR SHORT) |
Disconnect the SST from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A23-8 (BBP+) - A23-11 (BBP-) Always 1 MΩ or Higher
|
| ||||
OK | |
48.CHECK FLOOR WIRE (TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
- Standard voltage:
Tester Connection Condition Specified Condition A23-8 (BBP+) - Body ground Ignition switch ON Below 1 V A23-11 (BBP-) - Body ground Ignition switch ON Below 1 V
|
| ||||
OK | |
49.CHECK FLOOR WIRE (TO GROUND) |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition A23-8 (BBP+) - Body ground Always 1 MΩ or Higher A23-11 (BBP-) - Body ground Always 1 MΩ or Higher
|
| ||||
OK | |
50.CHECK CONNECTION OF CONNECTORS |
Check that the connectors are properly connected to the center airbag sensor assembly and the side airbag sensor assembly RH.
- OK:
- The connectors are properly connected.
|
| ||||
OK | |
51.CHECK CONNECTORS |
Check that the connectors (on the side airbag sensor assembly RH side and rear airbag sensor RH side) are not damaged (Click here).
- OK:
- The connectors are not deformed or damaged.
|
| ||||
OK | |
52.CHECK FLOOR WIRE (FOR OPEN) |
- SST
- 09843-18040
Disconnect the connectors from the side airbag sensor assembly RH and the rear airbag sensor RH.
Using SST, connect S14-1 (BCR-) and S14-2 (BCR+) of connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S12-1 (BCR+) - S12-2 (BCR-) Always Below 1 Ω
|
| ||||
OK | |
53.CHECK FLOOR WIRE (FOR SHORT) |
Disconnect the SST from connector C.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S12-1 (BCR+) - S12-2 (BCR-) Always Below 1 Ω
|
| ||||
OK | |
54.CHECK FLOOR WIRE (TO B+) |
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position.
Measure the voltage.
- Standard voltage:
Tester Connection Condition Specified Condition S12-1 (BCR+) - Body ground Ignition switch ON Below 1 V S12-2 (BCR-) - Body ground Ignition switch ON Below 1 V
|
| ||||
OK | |
55.CHECK FLOOR WIRE (TO GROUND) |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance.
- Standard resistance:
Tester Connection Condition Specified Condition S12-1 (BCR+) - Body ground Always 1 MΩ or Higher S12-2 (BCR-) - Body ground Always 1 MΩ or Higher
|
| ||||
OK | |
56.CHECK DTC |
Connect the connectors to the center airbag sensor assembly and side airbag sensor assembly.
- NOTICE:
- Do not connect the rear airbag sensor LH and the rear airbag sensor RH connector.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1620/21 and B1625/22 are not output.
- HINT:
- DTCs other than B1620/21 and B1625/22 may be output at this time, but they are not related to this check.
|
| ||||
OK | |
57.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
Turn the ignition switch to the LOCK position.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Connect the connectors to the rear airbag sensor LH and the rear airbag sensor RH.
Replace the center airbag sensor assembly (Click here).
- HINT:
- Perform the inspection using parts from a normal vehicle when possible.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Clear any DTCs stored in the memory (Click here).
Turn the ignition switch to the LOCK position.
Turn the ignition switch to the ON position, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1620/21 and B1625/22 are not output.
- HINT:
- DTCs other than B1620/21 and B1625/22 may be output at this time, but they are not related to this check.
|
| ||||
OK | ||
|