CLUTCH PEDAL > INSTALLATION |
for Preparation Click here
1. INSTALL CLUTCH PEDAL NO.1 CUSHION |
Install the clutch pedal No. 1 cushion to the clutch pedal sub-assembly.
2. INSTALL CLUTCH PEDAL SHAFT COLLAR |
Apply MP grease to the clutch pedal shaft collar.
Text in Illustration MP grease
Install the clutch pedal shaft collar to the clutch pedal sub-assembly.
3. INSTALL CLUTCH PEDAL BUSH |
Apply MP grease to 2 new bushes.
Text in Illustration MP grease
Install the 2 bushes to the clutch pedal sub-assembly.
4. INSTALL CLUTCH PEDAL PAD |
5. INSTALL CLUTCH PEDAL SPRING HOLDER |
Apply MP grease to the contact surface of the clutch pedal spring holder and clutch pedal support.
Text in Illustration MP grease
Install the clutch pedal spring holder.
6. INSTALL CLUTCH PEDAL SUB-ASSEMBLY |
Install the clutch pedal sub-assembly to the clutch pedal support with the bolt and nut.
- Torque:
- 34 N*m{ 347 kgf*cm , 25 ft.*lbf }
- HINT:
- Install the bolt from the left side of the vehicle.
7. INSTALL TURN OVER SPRING SEAT COMPRESSION SPRING |
Apply MP grease to the contact surfaces of the clutch pedal sub-assembly and the compression spring.
Text in Illustration MP grease
Install the compression spring to the clutch pedal sub-assembly and the clutch pedal spring holder.
8. INSTALL CLUTCH MASTER CYLINDER ASSEMBLY |
9. BLEED BRAKE LINE (for Vacuum Brake Booster) |
10. BLEED CLUTCH PIPE LINE |
11. INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY |
Lift the floor carpet.
Check that the pedal height is correct.
- Pedal height from asphalt sheet:
- 168.5 to 178.5 mm (6.634 to 7.028 in.)
Adjust the pedal height.
Loosen the lock nut and turn the stopper bolt until the height is correct. Tighten the lock nut.
- Torque:
- 25 N*m{ 250 kgf*cm , 18 ft.*lbf }
Check that the pedal free play and push rod play are correct.
Depress the pedal until the clutch resistance begins to be felt.
- Pedal free play:
- 5.0 to 15.0 mm (0.197 to 0.591 in.)
Gently depress the pedal until the resistance begins to increase a little.
- Push rod play at pedal top:
- 1.0 to 5.0 mm (0.039 to 0.197 in.)
Adjust the pedal free play and push rod play.
Loosen the lock nut and turn the push rod until the free play and push rod play are correct.
Tighten the lock nut.
After adjusting the pedal free play, check the pedal height.
Connect the air duct and install the lower finish panel.
Check the clutch release point.
Pull the parking brake lever and use wheel chocks.
Start the engine and allow it to idle.
Without depressing the clutch pedal, slowly move the shift lever into the reverse position until the gears engage.
Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.
- Standard distance:
- 25 mm (0.984 in.) or more
- (From pedal stroke end position to release point)
- Check the pedal height.
- Check the push rod play and pedal free play.
- Bleed the clutch line.
- Check the clutch cover assembly and disc assembly.
12. INSPECT FOR BRAKE FLUID LEAK (for Vacuum Brake Booster) |
13. INSPECT FOR CLUTCH FLUID LEAK |
14. INSPECT FLUID LEVEL IN RESERVOIR |