REAR SEAT OUTER BELT ASSEMBLY (for Double Cab) > INSTALLATION |
for Preparation Click here
1. INSTALL REAR SEAT OUTER BELT ASSEMBLY |
Check the amount of inclination required to lock the retractor.
Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any directions. Also check that the belt locks when inclination of the retractor is 45° or more.
- NOTICE:
- Do not disassemble the retractor.
Hook the lower stay of the retractor onto the 2 body hooks.
Tighten bolt A, and then tighten bolt B.
- Torque:
- 8.5 N*m{ 85 kgf*cm , 75 in.*lbf } (for bolt A)
- 42 N*m{ 430 kgf*cm , 31 ft.*lbf } (for bolt B)
Install the shoulder anchor with the bolt.
- Torque:
- 42 N*m{ 430 kgf*cm , 31 ft.*lbf }
Check that the shoulder anchor rotates smoothly.
Install the floor anchor with the bolt.
- Torque:
- 42 N*m{ 430 kgf*cm , 31 ft.*lbf }
- NOTICE:
- Make sure that the rear seat outer belt is oriented in the correct direction when installing.
- Be careful not to place the rear seat outer belt over the convex areas of the floor panel.
Check the ELR lock.
- NOTICE:
- The check should be performed with the rear seat outer belt installed.
- Do not allow the anchor part of the rear seat outer belt and the protruding parts of the floor panel to overlap.
With the belt installed, check that the belt locks when it is pulled out quickly.
If operation is not as specified, replace the rear seat outer belt.
Remove the bolt and floor anchor.
2. INSTALL QUARTER INSIDE TRIM BOARD |
Engage the 2 clips and install the quarter inside trim board.
Tighten the 3 screws.
Engage the claw and close the cover.
Install the floor anchor of the rear seat belt outer with the bolt.
- Torque:
- 42 N*m{ 430 kgf*cm , 31 ft.*lbf }
- NOTICE:
- The check should be performed with the rear seat outer belt installed.
- Do not allow the anchor part of the rear seat outer belt and the protruding parts of the floor panel to overlap.
3. INSTALL QUARTER TRIM LOWER PANEL |
Engage the 2 claws and 2 clips, and install the quarter trim lower panel.
4. INSTALL LUGGAGE COMPARTMENT SIDE TRAY |
w/ Woofer:
Engage the 5 claws and 7 clips, and install the luggage compartment side tray.
Tighten the bolt.
w/o Woofer:
Engage the 5 claws and 5 clips, and install the luggage compartment side tray.
Tighten the 3 bolts.
5. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP |
Install the rear door opening trim weatherstrip.
6. INSTALL REAR DOOR SCUFF PLATE |
Engage the 8 claws and install the rear door scuff plate.
7. INSTALL REAR SEAT BACK HINGE SUB-ASSEMBLY |
Install the rear seat back hinge with the 2 bolts.
- Torque:
- 18 N*m{ 185 kgf*cm , 14 ft.*lbf }
8. INSTALL REAR SEAT BACK ASSEMBLY |
Install the rear seat back with the 2 bolts.
- Torque:
- 37 N*m{ 375 kgf*cm , 27 ft.*lbf }
9. INSTALL REAR SEAT BACK HINGE COVER |
- HINT:
- Follow the same procedure as for the opposite side.
Engage the 3 claws and install the rear seat back hinge cover.