POWER WINDOW CONTROL SYSTEM > Rear Power Window RH does not Operate with Rear Power Window Switch RH |
for Preparation Click here
DESCRIPTION
If the rear RH side manual UP / DOWN function does not operate, a malfunction may exist in the rear power window regulator motor assembly RH, rear power window regulator switch assembly RH, power window regulator master switch assembly or wire harness.WIRING DIAGRAM
INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
1.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH |
Remove the rear power window regulator switch assembly RH.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Switch Condition Specified Condition 1 (U) - 3 (B)
4 (SD) - 5 (D)UP Below 1 Ω 2 (SU) - 1 (U)
4 (SD) - 5 (D)OFF Below 1 Ω 2 (SU) - 1 (U)
3 (B) - 5 (D)DOWN Below 1 Ω
Text in Illustration *a Component without harness connected
(Power Window Regulator Switch Assembly RH)
|
| ||||
OK | |
2.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH |
Remove the rear power window regulator motor assembly RH.
Apply battery voltage to connector terminals 1 and 2.
Check that the motor smoothly rotates.
- NOTICE:
- Do not apply battery voltage to any terminals except terminals 1 and 2.
- OK:
Measurement Condition Specified Condition Battery positive (+) → 2
Battery negative (-) → 1Motor gear rotates clockwise Battery positive (+) → 1
Battery negative (-) → 2Motor gear rotates counterclockwise
Text in Illustration *1 Motor Gear *a Clockwise *b Counterclockwise *c Component without harness connected
(Rear Power Window Regulator Motor Assembly)
|
| ||||
OK | |
3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - P/W RELAY) |
Disconnect the P16 rear power window regulator switch assembly RH connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection Switch Condition Specified Condition P16-3 (B) - Body ground Ignition switch ON 11 to 14 V
Text in Illustration *a Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly RH)
|
| ||||
OK | |
4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) |
Disconnect the P16 rear power window regulator switch assembly RH connector.
Disconnect the P13 rear power window regulator motor assembly RH connector.
Measure the resistance according the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition P16-1 (U) - P13-2 Always Below 1 Ω P16-5 (D) - P13-1 Always Below 1 Ω P16-1 (U) - Body ground Always 10 kΩ or higher P16-5 (D) - Body ground Always 10 kΩ or higher
|
| ||||
OK | |
5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY) |
Disconnect the P16 rear power window regulator switch assembly RH connector.
Disconnect the P9 power window regulator master switch assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection Condition Specified Condition P16-2 (SU) - P9-10 Always Below 1 Ω P16-4 (SD) - P9-18 Always Below 1 Ω P16-2 (SU) - Body ground Always 10 kΩ or higher P16-4 (SD) - Body ground Always 10 kΩ or higher
|
| ||||
OK | ||
|