SEAT POSITION SENSOR > INSTALLATION

for Preparation Click here


CAUTION:
Be sure to read the precautionary notices concerning the SRS airbag system before servicing it (Click here).


1. INSTALL SEAT POSITION AIRBAG SENSOR
  1. Using a 1 mm (0.039 in.) feeler gauge, install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm to 1.4 mm (0.023 to 0.055 in.).
  1. Using a T30 "torx" socket, tighten the "torx" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm to 1.4 mm (0.023 to 0.055 in.).

  1. Connect the connector.



    B127917E03
  1. Install the seat slide position sensor protector to the seat position sensor.



2. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)
  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.
  1. Connect the connector under the seat.

  1. Lift up the seat track adjusting handle and move the seat to the rearmost position.



    B131219E01
  1. Install the 2 bolts to the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.
  1. Lift up the seat track adjusting handle and move the seat to the foremost position.



    B131218E01
  1. Install the 2 bolts to the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the bolts in the order indicated in the illustration.


3. INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
  1. Place the seat in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.
  1. Connect the connectors under the seat.

  1. Connect the cable to the negative (-) battery terminal.



    B131273E01
  1. Operate the power seat switch knob and move the seat to the rearmost position.

  1. Install the 2 bolts to the front side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the 2 bolts in the order indicated in the illustration.


    B131274E01
  1. Operate the power seat switch knob and move the seat to the foremost position.

  1. Install the 2 bolts to the rear side of the seat.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    HINT:
    Tighten the 2 bolts in the order indicated in the illustration.


    B139933
  1. Install the front seat track bracket outer cover in the direction indicated by the arrow in the illustration and attach the 2 claws.



    B139934
  1. Install the front seat track bracket inner cover in the direction indicated by the arrow in the illustration and attach the 2 claws.



4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


5. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).