FRONT SEATBACK HEATER (for Power Seat) > REMOVAL |
for Preparation Click here
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
1. REMOVE FRONT SEAT ASSEMBLY |
2. REMOVE RECLINING POWER SEAT SWITCH KNOB |
Apply protective tape around the front seat cushion shield.
Using a screwdriver, detach the 2 claws and remove the reclining power seat switch knob.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1 Protective Tape
3. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB |
Apply protective tape around the front seat cushion shield.
Using a screwdriver, detach the 4 claws and remove the slide and vertical power seat switch knob.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1 Protective Tape
4. REMOVE FRONT SEAT CUSHION SHIELD LH |
Remove the 2 screws.
Remove the 3 screws.
Detach the claw and guide.
Remove the front seat cushion shield RH.
5. REMOVE FRONT SEAT INNER CUSHION SHIELD LH |
Remove the screw.
Detach the claw and guide.
Pull the front seat inner cushion shield RH to detach the claw and remove the front seat inner cushion shield RH.
6. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH |
Disconnect the connector and detach the 3 clamps.
Roll up the front seat cushion cover LH.
Remove the nut and front seat inner belt assembly.
Remove the buckle cover.
7. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
Detach the 4 front seat airbag wire harness clamps.
Disconnect the No. 1 seat wire connector and detach the wire harness clamp.
Detach the front seatback heater assembly LH wire harness clamp.
Remove the 2 screws, 4 bolts and separate type front seatback assembly.
8. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
Detach the guide and remove the reclining adjuster inside cover RH.
9. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
Detach the guide and remove the reclining adjuster inside cover LH.
10. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
w/o Front Seat Side Airbag:
Disconnect the No. 1 seat wire connector and detach the wire harness clamp.
Remove the hog rings from the wires of the separate type front seatback cover, and then roll up the separate type front seatback cover.
Pass the No. 1 seat wire through the hole of the separate type front seatback cover.
for LHD, w/ Seat Heater System:
Pass the front seatback heater assembly LH wire harness through the hole of the separate type front seatback cover.
Remove the hog rings and detach the strap of the separate type front seatback cover, and then roll up the separate type front seatback cover and No. 1 seatback cloth.
Pass the strap of the separate type front seatback cover through the holes of the separate type front seatback pad.
w/ Front Seat Side Airbag:
Remove the nut and detach the separate type front seatback cover bracket.
Remove the hog rings and roll up the separate type front seatback cover.
Text in Illustration *A w/o Front Seat Side Airbag *B w/ Front Seat Side Airbag *a Front view of front seatback *b Rear view of front seatback
Detach the 4 claws and remove the 2 front seat headrest supports and separate type front seatback cover from the separate type front seatback pad.
11. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH |
Cut off the tack pins which hold down the front seatback heater assembly LH, and then remove the front seatback heater assembly LH from the separate type front seatback cover.
- NOTICE:
- Be careful not to damage the separate type front seatback cover.