OUTPUT SHAFT > INSTALLATION

for Preparation Click here

1. Install the 3 No. 2 synchromesh shifting key springs and 3 synchromesh shifting keys to the No. 2 clutch hub.
   

   NOTICE:

   Be careful of the direction of the No. 2 hub sleeve and that of the No. 2 clutch hub.

2. Apply gear oil to the sliding part of the No. 2 hub sleeve, and install it to the No. 2 clutch hub.
   

1. Apply gear oil to the needle roller bearing, and install it to the output shaft.
   

1. Apply gear oil to the 3rd gear, and install it to the output shaft.
   

1. Apply gear oil to the No. 2 synchronizer ring, and install it to the 3rd gear.
   

1. Using SST and a press, press in the No. 2 clutch hub to the output shaft.
   

   SST

   09608-06041  
   

   NOTICE:

   1. Install the hub while aligning the key groove of the hub and the shifting key position.
      
   2. The 3rd gear should be able to rotate smoothly.
      

2. Select a snap ring that makes the clearance between the No. 2 clutch hub and snap ring to be within the specification.
   

   Standard clearance:

   0.10 mm (0.0039 in.) or less
   

   NOTICE:

   Do not damage the sliding surface of the bearing.

   Thickness

   1.80 to 1.85 mm (0.0709 to 0.0728 in.)

   1.85 to 1.90 mm (0.0728 to 0.0748 in.)

   1.90 to 1.95 mm (0.0748 to 0.0768 in.)

   1.95 to 2.00 mm (0.0768 to 0.0787 in.)

   2.00 to 2.05 mm (0.0787 to 0.0807 in.)

   2.05 to 2.10 mm (0.0807 to 0.0827 in.)

   2.10 to 2.15 mm (0.0827 to 0.0846 in.)

3. Using a snap ring expander, install the snap ring.
   

1. Apply gear oil to the needle roller bearing, and install it to the output shaft.
   

1. Apply gear oil to the 2nd gear, and install it to the output shaft.
   

1. Apply gear oil to the No. 1 synchronizer ring set, and install it to the 2nd gear.
   

1. Using a screwdriver, install the 3 synchromesh shifting key springs and 3 No. 1 synchromesh shifting keys to the No. 1 clutch hub.
   

2. Apply gear oil to the reverse gear, and install it to the No. 1 clutch hub.
   

1. Using SST and a press, press in the No. 1 clutch hub to the output shaft.
   

   SST

   09316-60011   (09316-00041)
   

   NOTICE:

   1. While performing (a) make sure that No. 1 synchronizer ring key groove and No. 1 synchromesh shifting key position are aligned.
      
   2. 1st gear should rotate freely.
      

2. Select a snap ring that makes the thrust clearance between the No. 1 clutch hub and snap ring to be within the specification.
   

   Standard clearance:

   0.10 mm (0.0039 in.) or less
   

   NOTICE:

   Do not damage the sliding surface of the bearing.

   Thickness

   2.30 to 2.35 mm (0.0906 to 0.0925 in.)

   2.35 to 2.40 mm (0.0925 to 0.0945 in.)

   2.40 to 2.45 mm (0.0945 to 0.0965 in.)

   2.45 to 2.50 mm (0.0965 to 0.0984 in.)

   2.50 to 2.55 mm (0.0984 to 0.1004 in.)

   2.55 to 2.60 mm (0.1004 to 0.1024 in.)

   2.60 to 2.65 mm (0.1024 to 0.1043 in.)

3. Using a brass bar and a hammer, tap in the snap ring.
   

1. Apply gear oil to the bearing spacer, and install it to the output shaft.
   

1. Apply gear oil to the needle roller bearing, and install it to the output shaft.
   

1. Install the thrust washer pin to the output shaft.
   

1. Apply gear oil to the No. 1 synchronizer ring set, and install them to the output shaft.
   

1. Apply gear oil to the No. 1 synchronizer ring set, and install them to the output shaft.
   

1. Apply gear oil to the 1st gear, and install it to the output shaft.
   

1. Apply gear oil to the thrust washer, and install it to the output shaft.
   

1. Using SST and a press, press in a new center bearing to the output shaft.
   

   SST

   09316-60011   (09316-00031)
   

   NOTICE:

   Install it so that the snap ring groove of the bearing faces to the rear side.

1. Using SST and a press, press in the 5th gear to the output shaft.
   

   SST

   09316-60011   (09316-00031)
   

   NOTICE:

   1. Check that the 5th gear and the spline of the output shaft fit before installing.
      
   2. Face the convex part of the gear to the front side.
      

1. Using a dial indicator, measure the thrust clearance.
   

   Standard clearance:

   0.30 to 0.55 mm (0.01181 to 0.02165 in.)
   

   If the clearance is not as specified, replace the No. 1 synchronizer ring.
   

1. Using a dial indicator, measure the thrust clearance.
   

   Standard clearance:

   0.10 to 0.25 mm (0.0039 to 0.0098 in.)
   

   If the clearance is not as specified, replace the No. 1 synchronizer ring set.
   

1. Using a feeler gauge, measure the thrust clearance.
   

   Standard clearance:

   0.10 to 0.25 mm (0.0039 to 0.0098 in.)
   

   If the clearance is not as specified, replace the No. 2 synchronizer ring.
   

1. Using a dial indicator, measure the radial clearance.
   

   Standard clearance:

   0.020 to 0.073 mm (0.0008 to 0.00029 in.)
   

   If the clearance is not as specified, replace the 1st gear needle roller bearing with a new one.
   

1. Using a dial indicator, measure the radial clearance.
   

   Standard clearance:

   0.015 to 0.068 mm (0.0006 to 0.0027 in.)
   

   If the clearance is not as specified, replace the 2nd gear needle roller bearing with a new one.
   

1. Using a dial indicator, measure the radial clearance.
   

   Standard clearance:

   0.015 to 0.068 mm (0.0006 to 0.0027 in.)
   

   If the clearance is not as specified, replace the 3rd gear needle roller bearing with a new one.