OIL PUMP > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT OIL PUMP BODY O-RING


D025646E01


2. FIX OIL PUMP ASSEMBLY


Q003426E01
  1. Place the oil pump body on the torque converter clutch.



3. REMOVE CLUTCH DRUM OIL SEAL RING


AT08412E01
  1. Remove the 2 oil seal rings.



4. REMOVE STATOR SHAFT THRUST BEARING RACE


AT08670E01


5. REMOVE STATOR SHAFT ASSEMBLY


AT08411E01
  1. Remove the 13 bolts, and then remove the stator shaft from the oil pump body.

  1. Remove the oil pump body from the torque converter clutch.



6. INSPECT FRONT OIL PUMP BODY


AT05153E01
  1. Using a dial indicator, measure the inside diameter of the oil pump body bush.

    Maximum inside diameter:
    38.19 mm (1.5035 in.)
    If the inside diameter is greater than the maximum, replace the oil pump body.


7. INSPECT STATOR SHAFT ASSEMBLY


AT05357E01
  1. Using a dial indicator, measure the inside diameter of the stator shaft bush.

    Maximum inside diameter:
    Front side
    Rear side
    21.58 mm (0.8496 in.)
    27.08 mm (1.0661 in.)
    If the inside diameter is greater than the maximum, replace the stator shaft.


8. INSPECT CLEARANCE OF FRONT OIL PUMP BODY


AT00153E01
  1. Push the driven gear to one side of the body.

  1. Using a feeler gauge, measure the clearance.

    Standard body clearance:
    0.07 to 0.15 mm (0.0028 to 0.0059 in.)

    Maximum body clearance:
    0.2 mm (0.0079 in.)
    If the body clearance is greater than the maximum, check the drive gear, driven gear and pump body.


    AT00154E01
  1. Using a feeler gauge, measure the tip clearance between the driven gear teeth and drive gear teeth.

    Standard tip clearance:
    0.004 to 0.248 mm (0.0002 to 0.0098 in.)

    Maximum tip clearance:
    0.3 mm (0.012 in.)
    If the tip clearance is greater than the maximum, check the drive gear, driven gear and pump body.


    AT00155E01
  1. Using a steel straightedge and feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.0008 to 0.0020 in.)

    Maximum side clearance:
    0.1 mm (0.004 in.)
    If the side clearance is greater than the maximum, check the drive gear, driven gear and pump body.

    HINT:
    There are 5 different thicknesses for drive and driven gears.

    Standard drive and driven gear thickness:
    Mark
    Specified Condition
    M
    11.690 to 11.699 mm (0.4602 to 0.4606 in.)
    N
    11.700 to 11.709 mm (0.4606 to 0.4610 in.)
    P
    11.710 to 11.720 mm (0.4610 to 0.4614 in.)
    R
    11.721 to 11.730 mm (0.4615 to 0.4618 in.)
    S
    11.731 to 11.740 mm (0.4618 to 0.4622 in.)


9. REMOVE FRONT OIL PUMP DRIVE GEAR


D025799E01


10. REMOVE FRONT OIL PUMP DRIVEN GEAR


D025800E01


11. REMOVE FRONT OIL PUMP OIL SEAL


AT05152E01
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the bush and the oil pump body.