FRONT WIPER MOTOR > INSTALLATION

for Preparation Click here



1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

  1. Using a T30 "TORX" socket, install the wiper motor with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


    E225942

  1. Connect the rod of the wiper link to the wiper motor.



    E225941E01

  1. Apply MP grease to the front wiper crank pivot of the windshield wiper motor assembly.

    Text in Illustration 
    *1
    		Crank Pivot
    V100145
    		MP grease


    E225943

  1. Connect the rod of the wiper link to the wiper motor.



2. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


B088000

  1. Move the wiper motor and link in the direction shown by the arrow in the illustration to attach the wiper cushion to the body, and install the wiper motor and link.

  1. Install the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Connect the connector.



3. INSTALL COWL TOP VENTILATOR LOUVER LH


    E225946

  1. Attach the 5 guides to install the cowl top ventilator louver LH.

  1. Install the clip.



4. INSTALL COWL TOP VENTILATOR LOUVER RH


    E225947

  1. Attach the 5 claws and 5 guides to install the cowl top ventilator louver RH.

  1. Install the clip.



5. INSTALL HOOD TO COWL TOP SEAL


B087996E03

  1. Attach the 9 clips and install the seal.



6. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. Operate the wiper and stop the front wiper motor and link at the automatic stop position.



    E177697E01

  1. Clean the wiper arm serration.

    Text in Illustration 
    *1
    		Wiper Arm Serrations
    *2
    		Wire Brush
    *3
    		Wiper Pivot Serrations

  1. When reusing the front wiper motor and link assembly.

    1. Clean the wiper pivot serrations with a wire brush.



    E225585E01

  1. Position the blade tip within the range shown in the illustration.

    HINT:
    The blade position is indicated by the mark on the glass.
    Text in Illustration 
    *1
    		Mark for Blade Position
    *a
    		Upper Limit
    *b
    		10 mm (0.393 in.)
    *c
    		Lower Limit

  1. Install the front wiper arm and blade assembly RH with the nut.

    Torque:
    20.5 N*m{ 209 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand when tightening the nut.


7. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. Operate the wiper and stop the front wiper motor and link at the automatic stop position.



    E177697E01

  1. Clean the wiper arm serrations.

    Text in Illustration 
    *1
    		Wiper Arm Serrations
    *2
    		Wire Brush
    *3
    		Wiper Pivot Serrations

  1. When reusing the front wiper motor and link assembly.

    1. Clean the wiper pivot serrations with a wire brush.



    E225586E01

  1. Position the blade tip within the range shown in the illustration.

    HINT:
    The blade position is indicated by the mark on the glass.
    Text in Illustration 
    *1
    		Mark for Blade Position
    *a
    		Upper Limit
    *b
    		10 mm (0.393 in.)
    *c
    		Lower Limit

  1. Install the front wiper arm and blade assembly RH with the nut.

    Torque:
    20.5 N*m{ 209 kgf*cm , 15 ft.*lbf }

    HINT:
    Hold the arm hinge by hand when tightening the nut.

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.



8. INSTALL FRONT WIPER ARM HEAD CAP

  1. Install the front wiper arm head cap.

    HINT:
    Use the same procedure for both front wiper arm head caps.


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).