BLIND SPOT MONITOR SYSTEM > OPERATION CHECK

for Preparation Click here



BLIND SPOT MONITOR BEAM AXIS INSPECTION

  1. Procedure to enter Test Mode

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.

    4. Turn the GTS on.

    5. Switch the blind spot monitor sensor to Test Mode using the GTS. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master beam axis inspection or BSM Slave beam axis inspection.

    6. Finish Test Mode.


BLIND SPOT MONITOR BEAM AXIS CONFIRMATION


  1. When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.


    E224418E07

    NOTICE:
    1. Perform this inspection on level ground.
    2. Make sure that there are no metal objects around the vehicle or on the ground.
    3. Unload the vehicle before beginning the inspection.
    4. Check that the tire pressure is correct before beginning the inspection.
    5. Do not place an object other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 9 m (29.53 ft) x L 10 m (32.81 ft) x H 4 m (13.12 ft)) shown in the illustration.
    6. Check that DTC C1ABB and DTC C1ABC are not output.


  2. Place the reflector.

    1. Hang a string (with weight) from the center of the vehicle's rear emblem. Mark the vehicle's rear center point on the ground. Repeat for the front of the vehicle. (mark (A) and (B))



      2. E238824E01

    2. Draw a vehicle center line so that it passes through mark (A) and (B) (front and rear center points).



      3. E238823E14

    3. Mark the position on the center line 593 mm (1.94 ft.) behind the rear bumper (for LH). (Mark (C))

      Text in Illustration 
      *a
      		for LH


      4. E238823E15

    4. Mark the position on the center line 589 mm (1.93 ft.) behind the rear bumper (for RH). (Mark (C))

      Text in Illustration 
      *a
      		for RH


      5. E238825E01

    5. Prepare 2 pieces of string of 600 mm (1.97 ft.) in length and secure the end of each string at a point 300 mm (11.8 in.) from mark (C) as shown in the illustration.



    6. Pull the end of each string and mark the position where each string meets on both the left and right side (marks (D) and (E)).


      E238826E01



      7. E238827E01

    7. Draw a line (P) so that it passes through mark (D) and (E) and is perpendicular to the vehicle center line.



    8. Set the reflector at the position (Z) shown in the illustration below.

      SST
      09870-60000   (09870-60010)
      09870-60040  

      E233794E13

      NOTICE:

      1. E238830E14
        Set the reflector so that its center is 465 mm (1.52 ft.) above the ground (for RH).
        Set the reflector so that its center is 653 mm (2.14 ft.) above the ground (for LH).
        Standard 

        		A
        Blind spot monitor sensor RH
        		465 mm
        (1.52 ft.)
        Blind spot monitor sensor LH
        		653 mm
        (2.14 ft.)

      2. E238829E01
        The center of triangular pyramid is the reference point for the setting position and angle.
      3. Set the reflector as shown in the illustration so that its center of triangular pyramid faces the blind spot monitor sensor.
      4. Perform the operation as precisely as possible.

  3. Perform the blind spot monitor beam axis display.

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the blind spot monitor main switch (warning canceling switch assembly) on.

    4. Turn the GTS on.

    5. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master beam axis display or BSM Slave beam axis display.

    6. Check the results displayed for the BSM beam axis display.

      Allowable Range:
      Item
      		Blind Spot Monitor Sensor RH (Master)
      		Blind Spot Monitor Sensor LH (Slave)
      Angle
      		-3.6 to +3.6 °
      		-3.6 to +3.6 °
      Distance
      		2.0 to 3.0 m
      (6.56 to 9.84 ft.)
      		2.0 to 3.0 m
      (6.56 to 9.84 ft.)

      HINT:
      If the results are outside the allowable range, try again as the reflector setting position may be incorrect or a metal object may exist near the detection area.

    7. Perform the blind spot monitor beam axis adjustment using the GTS. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Utility / BSM Master beam axis adjustment or BSM Slave beam axis adjustment.

      HINT:
      When values on the axis display are in the allowable range, performing this adjustment compensates the values to the normal value.

BLIND SPOT MONITOR INSTALLATION CONDITION INSPECTION

NOTICE:
  1. Perform this inspection on level ground.
  2. Unload the vehicle before beginning the inspection.
  3. Check that the tire pressure is correct before beginning the inspection.

  1. Remove the rear bumper (Click here).



  2. Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.


    E233717E01


    E233716E03

    Standard 

    		A
    		B
    Blind spot monitor sensor RH
    		8 mm
    (0.315 in)
    		-8 mm
    (-0.315 in)
    Blind spot monitor sensor LH
    		0 mm
    (0.0 in)
    		-17 mm
    (-0.669 in)

    HINT:
    Allowable ranges A and B are different between the blind spot monitor sensor LH and RH.


    3. E224437E08

  3. Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

    Standard:
    Dimension
    		Specified Value
    y
    		29 to 42 mm
    (1.14 to 1.65 in)