SHIFT LEVER > INSPECTION

for Preparation Click here



1. INSPECT LOWER SHIFT LEVER ASSEMBLY


    C239819E01

  1. Measure the voltage according to the value(s) in the table below.

    Text in Illustration 
    *a
    		Component with harness connected
    (Shift Lock Control ECU)

    Standard Voltage:
    Tester Connection
    		Condition
    		Specified Condition
    5 (IG) - Body ground
    		Engine switch on (IG)
    		11 to 14 V
    Engine switch off
    		Below 1 V
    4 (STP) - Body ground
    		Brake pedal depressed
    		11 to 14 V
    Brake pedal released
    		Below 1 V

    HINT:
    Do not disconnect the lower shift lever assembly connector.
    If the result is not as specified, replace the lower shift lever assembly.


    C239819E02

  1. Measure the resistance according to the value(s) in the table below.

    Text in Illustration 
    *a
    		Component with harness connected
    (Shift Lock Control ECU)

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    1 (E) - Body ground
    		Always
    		Below 1 Ω

    HINT:
    Do not disconnect the lower shift lever assembly connector.
    If the result is not as specified, replace the lower shift lever assembly.


  1. Inspect shift lock solenoid:



      C239826

    1. Disconnect the shift lock solenoid connector.



      2. C197452E09

    2. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

      Text in Illustration 
      *a
      		Front view of wire harness connector
      (to Shift Lock Solenoid)

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      4 (P) - 3 (E2)
      		Shift lever in P
      		10 kΩ or higher
      Shift lever not in P
      		Below 1 Ω
      1. If the result is not as specified, replace the lower shift lever assembly.
      2. If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      		Condition
      		Specified Condition
      1 (SLS+) - 2 (SLS-)
      		Always
      		112 Ω
      1. If the result is not as specified, replace the lower shift lever assembly.
      2. If the shift lock does not operate when the power source of the lower shift lever assembly is normal and the resistance between body ground and the shift lock solenoid is as specified, replace the lower shift lever assembly.


2. INSPECT TRANSMISSION CONTROL SWITCH


    C239095E09

  1. Measure the resistance between each terminal of the transmission control switch when the shift lever is moved to each position.

    Text in Illustration 
    *a
    		Component without harness connected
    (Transmission Control Switch)

    Standard Resistance:
    Tester Connection
    		Condition
    		Specified Condition
    4 (IG) - 5 (S)
    		Shift lever in S, "+" or "-"
    		Below 1 Ω
    Shift lever not in S, "+" or "-"
    		10 kΩ or higher
    3 (SFTU) - 2 (E)
    		Shift lever held in "+"
    (Up-shift)
    		Below 1 Ω
    Shift lever not held in "+"
    		10 kΩ or higher
    1 (SFTD) - 2 (E)
    		Shift lever held in "-"
    (Down-shift)
    		Below 1 Ω
    Shift lever not held in "-"
    		10 kΩ or higher
    If the result is not as specified, replace the lower shift lever assembly.