OUTER REAR VIEW MIRROR (for TMC, TMMR Made) > INSPECTION |
for Preparation Click here
| 1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Memory) |
Check the operation of the mirror surface.
Disconnect the outer rear view mirror assembly RH connector.
Apply battery voltage and check the operation of the mirror.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)Turns upward Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 6 (MV)Turns downward Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)Turns left Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 4 (MH)Turns right
If the result is not as specified, replace the outer rear view mirror assembly RH.Text in Illustration *a Component without harness connected
(Outer Rear View Mirror Assembly RH)
Check the operation of the retractable mirror.
- NOTICE:
- Disconnect and reconnect the battery between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
Disconnect the outer rear view mirror assembly RH connector.
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.
- OK:
Tester Connection Condition Specified Condition Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)Forward position (A) Moves from (A) to (E) Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)Position between forward position (A) and driving position (C) Moves from (B) to (E) Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)Position between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)Driving position (C) Moves from (C) to (E) Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)Position between driving position (C) and retracted position (E) Moves from (D) to (E) Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)Position between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)Retracted position (E) Does not move Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)Retracted position (E) Moves from (E) to (C)
If the result is not as specified, replace the outer rear view mirror assembly RH.Text in Illustration *1 (A) Forward Position *2 (B) *3 (C) Driving position *4 (D) *5 (E) Retracted Position *a Component without harness connected
(Outer Rear View Mirror Assembly RH)
Check the operation of the mirror heater.
Disconnect the outer rear view mirror assembly RH connector.
- HINT:
- The resistance of the mirror heater varies depending on the shape of the heater wire. Remove the mirror surface to check the shape of the heater wire before inspection.
- Remove the outer rear view mirror assembly RH (Click here).
- Check the shape of the heater wire (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Heater Wire Shape A Tester Connection Condition Specified Condition 2 (HR+) - 8 (HR-) 25°C (77°F) 7.6 to 11.4 Ω Heater Wire Shape B Tester Connection Condition Specified Condition 2 (HR+) - 8 (HR-) 25°C (77°F) 9.2 to 13.8 Ω
If the result is not as specified, replace the outer rear view mirror assembly RH.Text in Illustration *a Component without harness connected
(Outer Rear View Mirror Assembly RH)Connect the cable from the positive (+) terminal to terminal 2 and the negative battery (-) terminal to terminal 8, then check that the mirror becomes warm.
- HINT:
- It takes a short time for the mirror to become warm.
- OK:
- Mirror becomes warm.
| 2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Memory) |
Check the operation of the mirror surface.
Disconnect the outer rear view mirror assembly LH connector.
Apply battery voltage and check the operation of the mirror.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 6 (MV)
Battery negative (-) → Terminal 5 (M+)Turns upward Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 6 (MV)Turns downward Battery positive (+) → Terminal 4 (MH)
Battery negative (-) → Terminal 5 (M+)Turns left Battery positive (+) → Terminal 5 (M+)
Battery negative (-) → Terminal 4 (MH)Turns right
If the result is not as specified, replace the outer rear view mirror assembly LH.Text in Illustration *a Component without harness connected
(Outer Rear View Mirror Assembly LH)
Check the operation of the retractable mirror.
- NOTICE:
- Disconnect and reconnect the battery between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
Disconnect the outer rear view mirror assembly LH connector.
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.
- OK:
Tester Connection Condition Specified Condition Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)Forward position (A) Moves from (A) to (E) Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)Position between forward position (A) and driving position (C) Moves from (B) to (E) Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)Position between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)Driving position (C) Moves from (C) to (E) Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)Position between driving position (C) and retracted position (E) Moves from (D) to (E) Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)Position between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 9 (MF)Retracted position (E) Does not move Battery positive (+) → Terminal 9 (MF)
Battery negative (-) → Terminal 3 (MR)Retracted position (E) Moves from (E) to (C)
If the result is not as specified, replace the outer rear view mirror assembly LH.Text in Illustration *1 (A) Forward Position *2 (B) *3 (C) Driving position *4 (D) *5 (E) Retracted Position *a Component without harness connected
(Outer Rear View Mirror Assembly LH)
Check the operation of the mirror heater.
Disconnect the outer rear view mirror assembly LH connector.
- HINT:
- The resistance of the mirror heater varies depending on the shape of the heater wire. Remove the mirror surface to check the shape of the heater wire before inspection.
- Remove the outer rear view mirror assembly RH (Click here).
- Check the shape of the heater wire (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Heater Wire Shape A Tester Connection Condition Specified Condition 2 (HL+) - 8 (HL-) 25°C (77°F) 7.6 to 11.4 Ω Heater Wire Shape B Tester Connection Condition Specified Condition 2 (HL+) - 8 (HL-) 25°C (77°F) 9.2 to 13.8 Ω
If the result is not as specified, replace the outer rear view mirror assembly LH.Text in Illustration *a Component without harness connected
(Outer Rear View Mirror Assembly LH)Connect the cable from the positive (+) terminal to terminal 2 and the negative battery (-) terminal to terminal 8, then check that the mirror becomes warm.
- HINT:
- It takes a short time for the mirror to become warm.
- OK:
- Mirror becomes warm.
| 3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Memory) |
Check the operation of the mirror surface.
Disconnect the outer rear view mirror assembly RH connector.
Apply battery voltage and check the operation of the mirror.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 10 (M+)Turns upward Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 1 (MV)Turns downward Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 10 (M+)Turns left Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 9 (MH)Turns right
If the result is not as specified, replace the outer rear view mirror assembly RH.Text in Illustration *a Component without harness connected
(Outer Rear View Mirror Assembly RH)
Check the operation of the retractable mirror.
- NOTICE:
- Disconnect and reconnect the battery between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
Disconnect the outer rear view mirror assembly RH connector.
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
- OK:
Tester Connection Condition Specified Condition Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Forward position (A) Moves from (A) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Position between forward position (A) and driving position (C) Moves from (B) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Position between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Driving position (C) Moves from (C) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Position between driving position (C) and retracted position (E) Moves from (D) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Position between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Retracted position (E) Moves from (E) to (C)
If the result is not as specified, replace the outer rear view mirror assembly RH.Text in Illustration *1 (A) Forward Position *2 (B) *3 (C) Driving position *4 (D) *5 (E) Retracted Position *a Component without harness connected
(Outer Rear View Mirror Assembly RH)
Check the operation of the mirror heater.
Disconnect the outer rear view mirror assembly RH connector.
- HINT:
- The resistance of the mirror heater varies depending on the shape of the heater wire. Remove the mirror surface to check the shape of the heater wire before inspection.
- Remove the outer rear view mirror assembly RH (Click here).
- Check the shape of the heater wire (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Heater Wire Shape A Tester Connection Condition Specified Condition 4 (HTR+) - 12 (HTR-) 25°C (77°F) 7.6 to 11.4 Ω Heater Wire Shape B Tester Connection Condition Specified Condition 4 (HTR+) - 12 (HTR-) 25°C (77°F) 9.2 to 13.8 Ω
If the result is not as specified, replace the outer rear view mirror assembly RH.Text in Illustration *a Component without harness connected
(Outer Rear View Mirror Assembly RH)Connect the cable from the positive (+) terminal to terminal 4 and the negative battery (-) terminal to terminal 12, then check that the mirror becomes warm.
- HINT:
- It takes a short time for the mirror to become warm.
- OK:
- Mirror becomes warm.
| 4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Memory) |
Check the operation of the mirror surface.
Disconnect the outer rear view mirror assembly LH connector.
Apply battery voltage and check the operation of the mirror.
- OK:
Measurement Condition Specified Condition Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 10 (M+)Turns upward Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 1 (MV)Turns downward Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 10 (M+)Turns left Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 9 (MH)Turns right
If the result is not as specified, replace the outer rear view mirror assembly LH.Text in Illustration *a Component without harness connected
(Outer Rear View Mirror Assembly LH)
Check the operation of the retractable mirror.
- NOTICE:
- Disconnect and reconnect the battery between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
Disconnect the outer rear view mirror assembly LH connector.
For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
- OK:
Tester Connection Condition Specified Condition Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Forward position (A) Moves from (A) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Position between forward position (A) and driving position (C) Moves from (B) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Position between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Driving position (C) Moves from (C) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Position between driving position (C) and retracted position (E) Moves from (D) to (E) Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Position between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)Retracted position (E) Moves from (E) to (C)
If the result is not as specified, replace the outer rear view mirror assembly LH.Text in Illustration *1 (A) Forward Position *2 (B) *3 (C) Driving position *4 (D) *5 (E) Retracted Position *a Component without harness connected
(Outer Rear View Mirror Assembly LH)
Check the operation of the mirror heater.
Disconnect the outer rear view mirror assembly LH connector.
- HINT:
- The resistance of the mirror heater varies depending on the shape of the heater wire. Remove the mirror surface to check the shape of the heater wire before inspection.
- Remove the outer rear view mirror assembly RH (Click here).
- Check the shape of the heater wire (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Heater Wire Shape A Tester Connection Condition Specified Condition 4 (HTR+) - 12 (HTR-) 25°C (77°F) 7.6 to 11.4 Ω Heater Wire Shape B Tester Connection Condition Specified Condition 4 (HTR+) - 12 (HTR-) 25°C (77°F) 9.2 to 13.8 Ω
If the result is not as specified, replace the outer rear view mirror assembly LH.Text in Illustration *a Component without harness connected
(Outer Rear View Mirror Assembly LH)Connect the cable from the positive (+) terminal to terminal 4 and the negative battery (-) terminal to terminal 12, then check that the mirror becomes warm.
- HINT:
- It takes a short time for the mirror to become warm.
- OK:
- Mirror becomes warm.
