POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows) > HOW TO PROCEED WITH TROUBLESHOOTING

for Preparation Click here


HINT:
  1. Use the following procedure to troubleshoot the power window control system.
  2. *: Use the GTS.


1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS

      HINT:
      1. In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      2. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
      3. The following 5 items are important points for problem analysis:

        What
        Vehicle model, system name
        When
        Date, time, occurrence frequency
        Where
        Road conditions
        Under what conditions?
        Driving conditions, weather conditions
        How did it happen?
        Problem symptoms

    NEXT


    3.PRE-CHECK
    1. Measure the battery voltage.

      Standard Voltage:
      11 to 14 V
      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
    2. Check the fuses and relays.

    3. Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.


    NEXT


    4.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
    1. Using the GTS, check for CAN communication system DTCs (Click here).

      Result:
      Result
      Proceed to
      CAN DTCs are not output
      A
      CAN DTCs are output
      B


    B.
    GO TO CAN COMMUNICATION SYSTEM (Click here)
    A


    5.CHECK COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
    1. Using the GTS, check for LIN communication system DTCs (Click here).

      Result:
      Result
      Proceed to
      LIN DTCs are not output
      A
      LIN DTCs are output
      B


    B.
    GO TO LIN COMMUNICATION SYSTEM (Click here)
    A


    6.CHECK FOR DTC*
    1. Check for DTCs and make a note of any codes that are output (Click here).

    2. Clear the DTCs.

    3. Recheck for DTCs.

      Result:
      Result
      Proceed to
      DTCs are not output
      A
      DTCs are output
      B


    B.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
    A


    7.PROBLEM SYMPTOMS TABLE
    1. Refer to Problem Symptoms Table (Click here).

      Result:
      Result
      Proceed to
      Fault is not listed in Problem Symptoms Table
      A
      Fault is listed in Problem Symptoms Table
      B


    B.
    Go to step 10
    A


    8.OVERALL ANALYSIS AND TROUBLESHOOTING*
    1. Operation Check (Click here)

    2. Terminals of ECU (Click here)

    3. Data List / Active Test (Click here)

    4. Fail-safe Chart (Click here)

    5. Inspection


    NEXT


    9.ADJUST, REPAIR OR REPLACE
    1. Check if any of the front door window regulators, power window regulator motor assembly (for driver door) or power window regulator motor assembly (for front passenger door), door glass or door glass runs have been removed and reinstalled.

      Result:
      Result
      Proceed to
      Any of the door window regulators, power window regulator motor assembly (for driver door) or power window regulator motor assembly (for front passenger door), door glass or door glass runs have been removed and reinstalled
      A
      The door window regulators, power window regulator motor assembly (for driver door) or power window regulator motor assembly (for front passenger door), door glass and door glass runs have not been removed and reinstalled
      B


    B.
    Go to step 12
    A


    10.INITIALIZE POWER WINDOW CONTROL SYSTEM
    1. If any of the front door window regulators, power window regulator motor assembly (for driver door) or power window regulator motor assembly (for front passenger door), door glass or door glass runs have been removed and reinstalled, perform "Initialize Power Window Control System" for the applicable door glass (Click here).


    NEXT


    11.CONFIRMATION TEST

      NEXT

      END