HOOD LOCK CONTROL CABLE ASSEMBLY (for TMC, TMMR Made) > REMOVAL |
for Preparation Click here
1. REMOVE FRONT BUMPER ASSEMBLY |
2. REMOVE FRONT WHEEL LH (for LHD) |
3. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for LHD) |
- HINT:
- Use the same procedure for the RH side and LH side (Click here).
4. REMOVE FRONT FENDER LINER LH (for LHD) |
- HINT:
- Use the same procedure for the RH side and LH side (Click here).
5. REMOVE FRONT WHEEL RH (for RHD) |
6. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (for RHD) |
for TMC, TMMR Made:
Remove the 3 screws and front wheel opening extension pad RH.
for TMMK Made:
Remove the 3 screws and front wheel opening extension pad RH.
7. REMOVE FRONT FENDER LINER RH (for RHD) |
for TMC, TMMR Made:
Remove the clip.
Using a screwdriver, turn the pin 90 degrees counterclockwise and remove the pin hold clip.
Text in Illustration *a 90° Remove the 5 screws.
Text in Illustration *1 Grommet Remove the 4 clips, 2 grommets and front fender liner RH.
- HINT:
- The grommets need to be replaced with new ones because they will break when they are removed.
for TMMK Made:
Remove the clip.
Using a screwdriver, turn the pin 90 degrees counterclockwise and remove the pin hold clip.
Text in Illustration *a 90° Remove the 5 screws and bolt.
Text in Illustration *1 Grommet Remove the 4 clips, 3 grommets and front fender liner RH.
- HINT:
- The grommets need to be replaced with new ones because they will break when they are removed.
8. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD) |
Disengage the 10 claws and remove the front door scuff plate LH.
9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD) |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
10. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD) |
- HINT:
- Use the same procedure for the RH side and LH side (Click here).
11. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD) |
- HINT:
- Use the same procedure for the RH side and LH side (Click here).
12. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
13. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.
14. REMOVE HOOD LOCK ASSEMBLY (for LHD) |
Using a screwdriver, remove the hood lock nut cap.
Text in Illustration *1 Protective Tape - HINT:
- Tape the screwdriver tip before use.
Disconnect the connector.
Remove the 2 bolts and hood lock bolt.
Text in Illustration *1 Hood Lock Bolt
Disconnect the hood lock control cable assembly and remove the hood lock assembly.
15. REMOVE HOOD LOCK ASSEMBLY (for RHD) |
Using a screwdriver, remove the hood lock nut cap.
Text in Illustration *1 Protective Tape - HINT:
- Tape the screwdriver tip before use.
Disconnect the connector.
Remove the 2 bolts and hood lock bolt.
Text in Illustration *1 Hood Lock Bolt
Disconnect the hood lock control cable assembly and remove the hood lock assembly.
16. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD) |
Using a screwdriver, disengage the 5 clamps and hood cable grommet as shown in the illustration.
Text in Illustration *1 Hood Lock Control Cable *2 Hood Cable Grommet *3 Washer Hose *4 Hood Lock Control Cable Clamp - HINT:
- Tape the screwdriver tip before use.
Pull the hood lock control cable assembly from the engine compartment and remove it.
17. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD) |
Using a screwdriver, disengage the 4 clamps and hood cable grommet as shown in the illustration.
Text in Illustration *1 Hood Lock Control Cable *2 Hood Cable Grommet *3 Washer Hose *4 Hood Lock Control Cable Clamp - HINT:
- Tape the screwdriver tip before use.
Pull the hood lock control cable assembly from the engine compartment and remove it.