FRONT BRAKE > INSTALLATION |
for Preparation Click here
- HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
1. INSTALL FRONT DISC |
Align the matchmarks of the front disc and front axle hub, and install the front disc.
Text in Illustration *a Matchmark - NOTICE:
- When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.
2. INSTALL FRONT DISC BRAKE BUSHING DUST BOOT |
Secure the front disc brake cylinder mounting in a vise.
Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bushing dust boots.
Text in Illustration Lithium Soap Base Glycol Grease - HINT:
- Apply at least 0.3 g (0.01 oz) of lithium soap base glycol grease to each front disc brake bushing dust boot.
Using a socket wrench (19 mm) and a hammer, install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.
3. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING |
Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.
- Torque:
- 107 N*m{ 1090 kgf*cm , 79 ft.*lbf }
4. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING |
Apply a light layer of lithium soap base glycol grease to the contact surface of the No. 2 front disc brake cylinder slide pin.
Text in Illustration Lithium Soap Base Glycol Grease
Install a new front disc brake cylinder slide bushing to the front No. 2 disc brake cylinder slide pin.
5. INSTALL FRONT NO. 2 DISC BRAKE CYLINDER SLIDE PIN |
Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front No. 2 disc brake cylinder slide pin.
Text in Illustration Lithium Soap Base Glycol Grease
Install the front No. 2 disc brake cylinder slide pin to the front disc brake cylinder mounting.
Push the front No. 2 disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.
6. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN |
Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the front disc brake cylinder slide pin.
Text in Illustration Lithium Soap Base Glycol Grease
Install the front disc brake cylinder slide pin to the front disc brake cylinder mounting.
Push the front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin to the boot.
7. INSTALL FRONT DISC BRAKE FITTING KIT |
Install the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates to the front disc brake cylinder mounting.
Text in Illustration *1 Front No. 1 Disc Brake Pad Support Plate *2 Front No. 2 Disc Brake Pad Support Plate - NOTICE:
- Be sure to install each front disc brake pad support plate in the correct position and direction.
8. INSTALL FRONT ANTI-SQUEAL SHIM KIT |
Install the front disc brake pad wear indicator plate to each front disc brake pad.
- NOTICE:
- Install each front disc brake pad wear indicator plate in the correct position and direction.
Apply disc brake grease to the inside of each front disc brake anti-squeal shim as shown in the illustration.
Text in Illustration Disc Brake Grease
Install the front disc brake anti-squeal shim to each front disc brake pad.
- NOTICE:
- Install the front disc brake anti-squeal shims in the correct positions and directions.
- Disc brake grease can seep out slightly from the area where the front disc brake anti-squeal shim is installed.
- Make sure that disc brake grease is not applied onto the lining surface.
9. INSTALL FRONT DISC BRAKE PAD KIT |
Install the 2 front disc brake pads with front anti-squeal shim kit to the front disc brake cylinder mounting.
- NOTICE:
- There should be no oil or grease on the friction surfaces of the disc brake pads or the front disc.
Install the 2 anti-squeal springs to the front disc brake pads.
- NOTICE:
- When replacing the front disc brake pads with new ones, make sure to replace the anti-squeal springs at the same time.
- Be sure to install the anti-squeal springs into the front disc brake pad installation holes as far as they will go.
10. INSTALL DISC BRAKE CYLINDER ASSEMBLY |
Hold the front disc brake cylinder slide pin, and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.
Text in Illustration *a Hold *b Turn - Torque:
- 34 N*m{ 350 kgf*cm , 25 ft.*lbf }
11. CONNECT FRONT FLEXIBLE HOSE |
Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.
Text in Illustration *a Lock Hole - Torque:
- 29 N*m{ 300 kgf*cm , 22 ft.*lbf }
- NOTICE:
- Install the flexible hose lock securely into the lock hole in the front disc brake cylinder.
12. BLEED BRAKE LINE |
13. INSTALL FRONT WHEEL |
- Torque:
- 103 N*m{ 1049 kgf*cm , 76 ft.*lbf }