POWER WINDOW REGULATOR MOTOR > INSTALLATION

for Preparation Click here

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor.

1. Using a "TORX" driver (T25), install the power window regulator motor assembly with the 3 screws.
   

   Torque:

   5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

   HINT:

   The new rear window regulator adopts a self-tapping method. The installation position of the regulator will be threaded when the self-tapping screw is inserted.

1. Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.
   

2. Install the temporary bolt to the rear door window regulator sub-assembly.
   

3. Temporarily install the window regulator.
   

4. Tighten the 4 bolts in the order shown in the illustration to install the rear door window regulator.
   

   Torque:

   8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

5. Connect the connector.
   

1. Install the rear door glass run.
   

1. Slide the rear door glass sub-assembly to install it as shown in the illustration.
   

1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.
   

2. Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.
   

1. Insert the rear door lower window frame sub-assembly from above.
   

2. Install the rear door glass run to the rear door lower window frame sub-assembly.
   

3. Install the rear door lower window frame sub-assembly with the 2 bolts and screw.
   

1. Apply butyl tape to the rear door panel.
   

2. Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
   

3. Install the new rear door service hole cover.
   

   NOTICE:

   Securely install the rear door service hole cover avoiding wrinkles and air bubbles.

4. Connect the connector and clamp.
   

1. Engage the 3 claws to install the rear door inner glass weatherstrip.
   

1. Connect the rear door lock remote control cable and rear door inside locking cable to the rear inside handle.
   

2. Engage the 2 claws and install the rear door inside handle sub-assembly.
   

1. Engage the claw to install the No. 1 door scuff plate clamp.
   

2. Connect each connector.
   

3. Engage the rear door trim board with the 4 clips of the rear door inner glass weatherstrip.
   

4. Engage the 7 clips to install the rear door trim board to the rear door panel.
   

5. Install the 3 screws.
   

1. Install the rear ash receptacle assembly.
   

1. Engage the 6 claws and install the door assist grip cover.
   

1. Engage the 3 claws to install the rear door inside handle bezel plug.
   

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor.

1. Using a "TORX" driver (T25), install the front power window regulator motor sub-assembly with the 3 screws.
   

   Torque:

   5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

   HINT:

   A new front window regulator adopts a self-tapping method. The installation position of the regulator will be threaded when the self-tapping screw is inserted.

1. Apply MP grease to the sliding parts of the front door window regulator sub-assembly.
   

2. Install the temporary bolt to the front door window regulator sub-assembly.
   

3. Temporarily install the window regulator.
   

4. Tighten the 6 bolts in the order shown in the illustration to install the front window regulator.
   

   Torque:

   8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.
   

2. Install the front door glass sub-assembly with the 2 bolts.
   

   Torque:

   5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

1. Apply butyl tape to the front door panel.
   

2. Pass the front door lock remote control cable and rear door inside locking cable through a new front door service hole cover.
   

3. Install the new service hole cover.
   

   NOTICE:

   Securely install the front door service hole cover avoiding wrinkles and air bubbles.

4. Connect each connector and each clamp.
   

1. Install the front No. 1 speaker assembly with the 4 bolts.
   

2. Connect the connector.
   

1. Engage the 4 claws and install the front door inner glass weatherstrip.
   

1. Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.
   

2. Engage the 2 claws and install the front door inside handle sub-assembly.
   

1. Connect each connector.
   

2. Engage the front door trim board with the 4 clips of the front door inner glass weatherstrip.
   

3. Engage the 9 clips and install the front door trim board to the front door panel.
   

4. Install the 3 screws and clip (A).
   

1. Connect the connector.
   

2. Engage the claw and install the courtesy light assembly.
   

1. Engage the 6 claws and install the assist grip cover.
   

1. Engage the 3 claws and install the front door inside handle bezel plug.
   

1. Engage the 2 clips and install the front door lower frame bracket garnish.