PARKING BRAKE PEDAL > INSTALLATION

for Preparation Click here



1. INSTALL PARKING BRAKE PEDAL ASSEMBLY (for LHD)


    C143766
  1. Install the parking brake pedal assembly with the bolt and 2 nuts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
  1. Connect the parking brake switch connector.



  1. Install the No. 1 parking brake cable assembly to the body with the bolt, the nut, and a new No. 1 parking brake cable clamp.


    C133453

    Torque:
    Bolt:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }
    Nut:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


    C133438
  1. Using a brass bar and a hammer, install the clip to the No. 1 parking brake cable assembly.



2. INSTALL PARKING BRAKE PEDAL ASSEMBLY (for RHD)


    C132690
  1. Install the parking brake pedal assembly with the bolt and 2 nuts.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }
  1. Connect the parking brake switch connector.



    C133447
  1. Install the No. 1 parking brake cable assembly to the body with the bolt.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }


    C133438
  1. Using a brass bar and a hammer, install the clip to the No. 1 parking brake cable sub-assembly.



3. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for RHD)


    C133468
  1. Engage the 3 claws and install the No. 1 air duct sub-assembly.



4. CONNECT NO. 4 PARKING BRAKE CABLE ASSEMBLY
  1. Connect the No. 4 parking brake cable assembly to the No. 1 parking brake cable assembly.



    C143746E01
  1. Using SST and a wrench, hold the lock nut of the No. 1 parking brake cable and tighten the turnbuckle of the No. 4 parking brake cable assembly.

    SST
    09023-00101  

    Torque:
    without SST:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    with SST:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).
    2. This torque is effective when SST is parallel to a torque wrench.


5. INSTALL CENTER AIRBAG SENSOR ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.


    C133884E01
  1. Install the center airbag sensor assembly with the 3 bolts.

    Torque:
    17.5 N*m{ 179 kgf*cm , 13 ft.*lbf }

    NOTICE:
    1. If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
  1. Check that there is no looseness in the installation parts of the center airbag sensor assembly.

  1. Connect the holder (with connectors).

  1. Check that the water-proof sheet is properly set.



6. INSTALL FLOOR SHIFT LEVER ASSEMBLY


    C132691
  1. Install the floor shift lever assembly with the 4 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 8.9 ft.*lbf }


7. INSTALL YAW RATE AND ACCELERATION SENSOR (w/ VSC)


    C133329
  1. Install the yaw rate and acceleration sensor with the 2 bolts.

    NOTICE:
    1. Do not damage the yaw rate and acceleration sensor.
    2. Make sure that the yaw rate and acceleration sensor is installed securely.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }
  1. Connect the yaw rate and acceleration sensor connector.



8. INSTALL FLOOR CARPET BRACKET LH


9. INSTALL FLOOR CARPET BRACKET RH


10. INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    C129716
  1. Install the No. 1 console box duct with the clip.



11. INSTALL NO. 2 CONSOLE BOX INSERT FRONT


    B134005E01
  1. Engage the clip.

  1. Install the No. 2 console box insert front with the 3 screws <F>.



12. INSTALL NO. 1 CONSOLE BOX INSERT FRONT


    B134006E01
  1. Engage the clip.

  1. Install the No. 1 console box insert front with the 3 screws <F>.



13. INSTALL CONSOLE BOX ASSEMBLY


    B134002E01
  1. Install the 2 screws <F>.



    B134003E01
  1. Install the console box assembly with the 2 bolts <G>.



14. INSTALL CONSOLE BOX CARPET


    B134004
  1. Install the console box carpet.



15. INSTALL CONSOLE BOX POCKET
  1. Install the console box pocket.



16. INSTALL LOWER INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY
  1. Connect each connector.



    B141243E01
  1. Engage the 2 claws and 2 clips.

  1. Install the lower instrument cluster finish panel center sub-assembly with the 2 screws <F>.



17. INSTALL UPPER CONSOLE REAR PANEL SUB-ASSEMBLY


    B144603E01
  1. Connect the connector and engage the clamp.

  1. Engage the 3 claws and 5 clips to install the upper console rear panel sub-assembly.



18. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY
  1. with Seat Heater System:

    1. Connect each connector.



    B148447
  1. Engage the 6 claws and the 3 clips to install the floor shift position indicator housing sub-assembly.



19. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B144599
  1. Engage the 2 clips and install the No. 1 instrument cluster finish panel garnish.



20. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B144605
  1. Engage the 2 clips and install the No. 2 instrument cluster finish panel garnish.



21. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    B148448
  1. Install the shift lever knob sub-assembly.



22. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    B133992E01
  1. Engage the 3 claws and 3 clips.

  1. Install the 4 screws <B>.

  1. Install the lower instrument panel sub-assembly with the bolt <A>.



23. INSTALL INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY


    B133989E01
  1. Engage the 4 claws and 2 guides and install the instrument panel No. 2 under cover.



24. INSTALL COMBINATION METER ASSEMBLY (for RHD)


    B133987E01
  1. Connect each connector.

  1. Install the combination meter assembly with the 4 screws <E>.



25. INSTALL INSTRUMENT CLUSTER FINISH PANEL NO.1 (for RHD)


    B133985E01
  1. Engage the guide and the 4 claws.

  1. Install the instrument cluster finish panel with the 2 clips.



26. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)


    B144612
  1. Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.



27. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)
  1. Connect each connector.



    B133986
  1. Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.



28. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH


    B147263E01
  1. Install the air hose and connect the connector.

  1. Engage the 2 claws and the DLC3.

  1. Engage the claw and the 4 clips.

  1. Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.



29. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    B132116E01
  1. Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the cowl side trim clip.



30. INSTALL FRONT DOOR SCUFF PLATE LH


    B132067
  1. Engage the 7 claws and 3 clips, then install the front door scuff plate LH.



31. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.


32. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.


33. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


34. INSPECT SENSOR SIGNAL

HINT:
(Click here)