CHILD RESTRAINT SEAT TETHER ANCHOR > INSTALLATION

for Preparation Click here



1. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET


    B132027
  1. Install the 3 child restraint seat tether anchor brackets with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (for Fold Down Seat Type)


    B132022
  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

  1. Engage the 4 clips and 5 claws and install the package tray trim panel assembly.

  1. Connect the connector.



3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (for Reclining Seat Type)


    B132139
  1. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

  1. Engage the 4 clips and 5 claws and install the package tray trim panel assembly.

  1. Connect the connector.



4. INSTALL REAR SEAT SHOULDER BELT HOLE COVER


    B132014
  1. Engage the 4 claws and install the rear seat shoulder belt hole cover.



5. INSTALL REAR SEAT SHOULDER BELT COVER


    B132012
  1. Engage the 4 claws and install the rear seat shoulder belt cover.

    HINT:
    Use the same procedures for the RH side and the LH side.


6. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    B132008E01
  1. Install the floor end of the rear seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat outer belt assembly to overlap protruding parts of the floor panel.
  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.

    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.



7. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    B132009E01
  1. Install the floor end of the rear seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat outer belt assembly to overlap protruding parts of the floor panel.
  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.

    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.



8. INSTALL ROOF SIDE INNER GARNISH LH


    B132063
  1. Engage the 5 clips and 2 claws, then install the roof side inner garnish LH.



9. INSTALL ROOF SIDE INNER GARNISH RH

HINT:
Use the same procedures for the RH side and the LH side.


10. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    B132010E01
  1. Install the floor end of the rear seat inner with center belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the protruding parts of the floor panel.
  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the outer belt assembly installed.

    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.



11. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    B132028
  1. Install the child restraint seat anchor bracket sub-assembly with the 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


12. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH (for Reclining Seat Type)


    B139084
  1. Install the rear seat reclining control cable.



    B139083
  1. Engage the 2 clips and claw and then install the reclining remote control lever sub-assembly.

  1. Install the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


    B144036E01
  1. Adjust the control lever to set the rear reclining adjuster assembly to its upper most position.

  1. Pull plate A toward the front of the vehicle to lock the plate.



13. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH (for Reclining Seat Type)

HINT:
Use the same procedures for the RH side and the LH side.


14. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B132080E01
  1. Install the rear door opening trim weatherstrip LH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


15. INSTALL REAR DOOR SCUFF PLATE LH


    B132068
  1. Engage the 5 claws and 2 clips, then install the rear door scuff plate LH.



16. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B132082E01
  1. Install the rear door opening trim weatherstrip RH as shown in the illustration.

    NOTICE:
    After installation, check that the corners fit correctly.


17. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.


18. INSTALL CENTER SEATBACK ASSEMBLY (for Reclining Seat Type)


    B140592
  1. Install the center seatback assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


19. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)


    B139077
  1. Install the separate type rear seatback assembly LH with the 2bolts and 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


    B139081E01
  1. Engage the 3 clamps and install the cover.



    B139076E01
  1. Install the 2 rear seat belts.



20. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type)


    B139079
  1. Install the separate type rear seatback assembly RH with the 2 bolts and 2 nuts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


    B139082E01
  1. Engage the 3 clamps and install the cover.



    B139078E01
  1. Install the rear seat belt.



21. INSTALL REAR SEATBACK COVER (for Reclining Seat Type)


22. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    B136561
  1. Install the rear side seatback assembly with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


23. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

HINT:
Use the same procedures for the RH side and the LH side.


24. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    B136539
  1. Install the separate type rear seatback assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


25. INSTALL SEPARATE TYPE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)


    B134700
  1. Install the separate type rear seat back assembly with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


26. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY


27. INSTALL REAR SEAT HEADREST ASSEMBLY


28. INSTALL REAR SEAT CUSHION ASSEMBLY


    B140584E01
  1. Attach the front hooks of the bench type rear seat cushion assembly to the vehicle body.

  1. Confirm that the seat cushion is firmly installed.

    NOTICE:
    When installing the bench type rear seat cushion assembly, make sure that the seat belt buckle is not under the bench type rear seat cushion assembly.