CLUTCH PEDAL > INSTALLATION

for Preparation Click here

1. Apply MP grease to the inside of a new clevis bushing.
   

2. Install the clevis bushing to the clutch pedal.
   

   HINT:

   Install the clevis bushing from the left side of the vehicle.

1. Apply MP grease to the inside of the turnover bushing.
   

2. Install the turnover bushing to the clutch pedal.
   

1. Apply MP grease to the inside of the turnover bushing.
   

2. Install the turnover bushing to the clutch pedal.
   

1. Using needle-nose pliers, install the 2 No. 1 clutch pedal cushions to the clutch pedal.
   

1. Using needle-nose pliers, install the 2 No. 1 clutch pedal cushions to the clutch pedal.
   

1. Apply MP grease to the inner, outer and end surfaces of 2 new pedal bushings.
   

2. Install the clutch pedal shaft collar and 2 pedal bushings to the clutch pedal.
   

1. Install the clutch pedal pad to the clutch pedal.
   

1. Apply MP grease to the inside of a new clutch pedal spring holder.
   

2. Install the clutch pedal spring holder.
   

1. Install the clutch pedal to the clutch pedal support with the bolt and nut.
   

   Torque:

   37 N*m{ 375 kgf*cm , 27 ft.*lbf }

   HINT:

   Install the bolt from the right side of the vehicle.

1. Apply MP grease to the sliding portion of the spring.
   

2. Install the hook spring.
   

1. Apply MP grease to the sliding portion of the spring.
   

2. Install the torsion spring.
   

1. Install the clutch pedal support to the vehicle with the 2 nuts and bolt.
   

   Torque:

   Bolt:

   19 N*m{ 195 kgf*cm , 14 ft.*lbf }

   Nut:

   12 N*m{ 120 kgf*cm , 9 ft.*lbf }

1. Install the clutch pedal support to the vehicle with the 3 nuts and bolt.
   

   Torque:

   Bolt:

   19 N*m{ 195 kgf*cm , 14 ft.*lbf }

   Nut:

   12 N*m{ 120 kgf*cm , 9 ft.*lbf }

1. Apply MP grease to the contact surface of the pin and clevis bushing.
   

2. Connect the clevis to the clutch pedal with the pin and a new clip.
   

   HINT:

   Install the pin from the left side of the vehicle.

1. Connect the clutch start switch connector.
   

2. Connect the clutch switch connector (with cruise control).
   

1. Connect each connector.
   

2. Install the combination meter assembly with the 4 screws <E>.
   

1. Engage the guide and the 4 claws.
   

2. Install the instrument cluster finish panel with the 2 clips.
   

1. Engage the 2 claws and 2 clips to install the lower instrument panel finish panel.
   

1. Connect each connector.
   

2. Engage the 3 claws and 2 clips to install the No. 1 instrument panel sub-assembly.
   

1. Install the air hose and connect the connector.
   

2. Engage the 2 claws and the DLC3.
   

3. Engage the claw and the 4 clips.
   

4. Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.
   

1. Engage the 2 clips.
   

2. Install the cowl side trim sub-assembly LH with the cowl side trim clip.
   

1. Engage the 7 claws and 3 clips, then install the front door scuff plate LH.